GILBARCO VEEDER-ROOT Applause Media System Скачать руководство пользователя

Страница: 26 / 102

Start-up

Configuring Applause Media System

Page 4-4

MDE-4699L Applause™ Media System Installation, Service, and Parts Manual · June 2017

Enter the Gilbarco Site Server IP address (10.5.48.66). You will be prompted to enter a
username and password. Enter “gilbarco” as the username and “admin” as the password. The
Setup Screen appears.

Note: The server IP address may be different if the IP address that was programmed

previously was different from the default settings.

Figure 4-1: Setup Screen

Configuring Applause Media System

This section provides information on how to configure the Applause Media System.

To configure the Applause Media System, proceed as follows:

After you connect to the Gilbarco Site Server IP address, click

Click Here to Begin Setup

the Setup screen. The Set Date and Time screen appears.

Figure 4-2: Set Date and Time Screen

Note: Ensure that you select the correct time zone.

Содержание Applause Media System







































































































Результаты поиска

Содержание Applause Media System

Отзывы:

Похожие инструкции для Applause Media System

Бренды по названию

Популярные бренды

GILBARCO VEEDER-ROOT Applause Media System, Инструкция по установке, обслуживанию и ремонту

Результаты поиска

Содержание Applause Media System

Отзывы:

Похожие инструкции для Applause Media System

Бренды по названию

Популярные бренды