GigaDevice Semiconductor GD32VF103 Скачать руководство пользователя страница 348

Страница: 348 / 536

GD32VF103 User Manual

348

0: Even parity

1: Odd parity

PERRIE

Parity error interrupt enable

If this bit is set, an interrupt occurs when the PERR bit in USART_STAT is set.

0: Parity error interrupt is disabled

1: Parity error interrupt is enabled

TBEIE

Transmitter buffer empty interrupt enable

If this bit is set, an interrupt occurs when the TBE bit in USART_STAT is set.

0: Transmitter buffer empty interrupt is disabled

1: Transmitter buffer empty interrupt is enabled

TCIE

Transmission complete interrupt enable

If this bit is set, an interrupt occurs when the TC bit in USART_STAT is set.

0: Transmission complete interrupt is disabled

1: Transmission complete interrupt is enabled

RBNEIE

Read data buffer not empty interrupt and overrun error interrupt enable

If this bit is set, an interrupt occurs when the RBNE bit or the ORERR bit in

USART_STAT is set.

0: Read data register not empty interrupt and overrun error interrupt disabled

1: Read data register not empty interrupt and overrun error interrupt enabled

IDLEIE

IDLE line detected interrupt enable

If this bit is set, an interrupt occurs when the IDLEF bit in USART_STAT is set.

0: IDLE line detected interrupt disabled

1: IDLE line detected interrupt enabled

TEN

Transmitter enable

0: Transmitter is disabled

1: Transmitter is enabled

REN

Receiver enable

0: Receiver is disabled

1: Receiver is enabled

RWU

Receiver wakes up from mute mode.

Software can set this bit to make the USART work in mute mode and clear this bit

to wake up the USART.

If it is configured to wake up by idle frame (WM=0), this bit can be cleared by

hardware when an idle frame has been detected. If it is configured to wake up by

address matching (WM=1), this bit can be cleared by hardware when receiving an

address match frame or set by hardware when receiving an address mismatch

frame.

0: Receiver in active mode

1: Receiver in mute mode

Содержание GD32VF103

























































































































































































































































































































































































































































































































































Результаты поиска

Содержание GD32VF103

Отзывы:

Похожие инструкции для GD32VF103

Бренды по названию

Популярные бренды

GigaDevice Semiconductor GD32VF103, Руководство пользователя

Результаты поиска

Содержание GD32VF103

Отзывы:

Похожие инструкции для GD32VF103

Бренды по названию

Популярные бренды