GigaDevice Semiconductor GD32VF103 Скачать руководство пользователя страница 527

Страница: 527 / 536

GD32VF103 User Manual

527

These is a data PID toggle scheme in interrupt or bulk transfer. Software should set

SD0PID to set this bit before a transfer starts and USBFS maintains this bit during

transfers following the data toggle scheme described in USB protocol.

0: Data packet

’s PID is DATA0

1: Data packet

’s PID is DATA1

EPACT

Endpoint active

This bit controls whether this endpoint is active. If an endpoint is not active, it ignores

all tokens and doesn

’t make any response.

14:11

Reserved

Must be kept at reset value

10:0

MPL[10:0]

This field defines the maximum packet length in bytes.

Device IN endpoint-x interrupt flag register (USBFS_DIEPxINTF) (x = 0..3, where

x = endpoint_number)

Address offset: (endpoint_number × 0x20)

Reset value: 0x0000 0080

This register contains the status and events of an IN endpoint, when an IN endpoint interrupt

occurs, read this register for the respective endpoint to know the source of the interrupt. The

flag bits in this register are all set by hardware and cleared by writing 1 except the read-only

TXFE bit.

This register has to be accessed by word (32-bit)

Rese

rve
d

Rese

rve
d

IE
P

Rese

rve
d

CIT

Rese

rve
d

DIS

rc_w1

Bits

Fields

Descriptions

31:8

Reserved

Must be kept at reset value

TXFE

Transmit FIFO empty

The Tx FIFO of this IN endpoint has reached the empty threshold value defined by

TXFTH field in USBFS_GAHBCS register.

IEPNE

IN endpoint NAK effective

Содержание GD32VF103

























































































































































































































































































































































































































































































































































Результаты поиска

Содержание GD32VF103

Отзывы:

Похожие инструкции для GD32VF103

Бренды по названию

Популярные бренды

GigaDevice Semiconductor GD32VF103, Руководство пользователя

Результаты поиска

Содержание GD32VF103

Отзывы:

Похожие инструкции для GD32VF103

Бренды по названию

Популярные бренды