GigaDevice Semiconductor GD32VF103 Скачать руководство пользователя страница 236

Страница: 236 / 536

GD32VF103 User Manual

236

2) Configure CHxNP=0 (the active level of CHx_ON is low, contrary to OxCPRE), CHxNE=1

(the output of CHx_ON is enabled),

If the output of OxCPRE is active(high) level, the output of CHx_O is active(low) level;

If the output of OxCPRE is inactive(low) level, the output of CHx_O is active(high) level.

When CH0_O and CH0_ON are output at the same time, the specific outputs of CH0_O and

CH0_ON are related to the relevant bits (ROS, IOS, POE and DTCFG bits) in the

TIMERx_CCHP register. Please refer to

Complementary outputs

for more details.

In output compare mode, the TIMERx can generate timed pulses with programmable position,

polarity, duration and frequency. When the counter matches the value in the TIMERx_CHxCV

based on CHxCOMCTL. When the counter reaches the value in the TIMERx_CHxCV register,

the CHxIF bit will be set and the channel (n) interrupt is generated if CHxIE = 1. And the DMA

request will be asserted, if CxCDE=1.

So the process can be divided into several steps as below:

Step1:

Clock Configuration. Such as clock source, clock prescaler and so on.

Step2:

Compare mode configuration.



Set the shadow enable mode by CHxCOMSEN



Set the output mode (set/clear/toggle) by CHxCOMCTL.



Select the active polarity by CHxP/CHxNP



Enable the output by CHxEN

Step3:

Interrupt/DMA-request enable configuration by CHxIE/CHxDEN.

Step4:

Compare output timing configuration by TIMERx_CAR and TIMERx_CHxCV

The TIMERx_CHxCV can be changed ongoing to meet the expected waveform.

Step5:

Start the counter by configuring CEN to 1.

Figure 15-15. Output-compare in three modes

show the three compare modes

toggle/set/clear. CAR=0x63, CHxVAL=0x3

Содержание GD32VF103

























































































































































































































































































































































































































































































































































Результаты поиска

Содержание GD32VF103

Отзывы:

Похожие инструкции для GD32VF103

Бренды по названию

Популярные бренды

GigaDevice Semiconductor GD32VF103, Руководство пользователя

Результаты поиска

Содержание GD32VF103

Отзывы:

Похожие инструкции для GD32VF103

Бренды по названию

Популярные бренды