GESTRA LRG 16-60 Скачать руководство пользователя

Страница: 51 / 64

LRG 1x-6x - Installation & Operating Manual -

819878-00

Behaviour on the occurrence of alarms

The conductivity electrode
is immersed
The conductivity limit value is
exceeded = Alarm limit value
AL.Hi

Display:

Hi.C and 1234 alternately

LED 1

Alarm LED lights up red

The alarm signal and the actual measured value
are displayed alternately

The MAX alarm is active

LED 3 or 4

: lights up green

Display of the set unit

LED 2:

flashes green

The equipment is performing a self-test

LED 2:

is OFF

MAX alarm occurrence

■

The alarm state is transferred to the URS 60/URS 61 safety control unit via CAN data telegram.

■

Once the time delay has elapsed, the alarm signal triggers the safety shutoff.

■

The signal outputs are activated.

■

The URS 60/URS 61 safety control unit does not automatically lock the safety contacts.

Behaviour in the event of an error (fault code display)

The conductivity electrode
is immersed or not immersed.
There is an error.

Display:

e.g. E005

LED 1

Alarm LED lights up red

A fault code is permanently displayed;
fault code display see page 54

There is an active error

LED 3 or 43

: lights up green

Display of the set unit

LED 2:

flashes green

The equipment is performing a self-test

LED 2:

is OFF

Error or internal fault

■

The error or fault state is transferred to the URS 60/URS 61 safety control unit via
CAN data telegram.

■

The error causes this unit to execute the safety shutoff without a delay.

■

The URS 60/URS 61 safety control unit does not automatically lock the safety contacts.

Electrode alarms and errors faults cannot be acknowledged.

When the alarm or error is cancelled the display also goes blank, and the URS 60/URS 61
safety control unit closes the safety contacts again.

Start, operation, alarm and test

Содержание LRG 16-60

































































Результаты поиска

Содержание LRG 16-60

Отзывы:

Похожие инструкции для LRG 16-60

Бренды по названию

Популярные бренды

GESTRA LRG 16-60, Инструкция по установке и эксплуатации

Результаты поиска

Содержание LRG 16-60

Отзывы:

Похожие инструкции для LRG 16-60

Бренды по названию

Популярные бренды