manualshive.com logo in svg

Gerber GSx Plus, Руководство пользователя, Страница: 6 / 60

Поделиться
Скачать
Gerber GSx Plus Скачать руководство пользователя страница 6

 

 

 

5

Chapter 1: 
Introduction 

Description 

The GSx

plus

 

™

 is a state of the art 15-inch (38.1 cm) plotter designed for use with 

the OMEGA

®

 system and other sign design systems.  

 

Note: When the GSx

plus

 is used with other sign design systems, contact the 

system manufacturer to obtain a driver for the GSx

plus

. 

Performance 

The GSx

plus

 is designed to precisely register graphics up to 50 yards (45.7 meters) 

long using carbide blades for crisp, sharp cuts. It cuts up to 25% faster than 
comparable plotters for rapid cutting of all but the most demanding materials 
such as sandblast stencil.  Gerber's exclusive Corner Correcting Technology

™

 

assures sharp, easy-to-weed corners 

Able to handle complex jobs, the GSx

plus

 cuts at 4.7 inches (11.9 cm) per second 

(on a straight line). When used with OMEGA, the GSx

plus

 uses the Plot Spooler 

feature to receive and plot files while the operator continues to design at the 
system. 

Convenience 

The GSx

plus

 has many features that make it easy and convenient to use: 

ƒ

 

Accepts any standard Gerber materials in 15-inch wide rolls. 

ƒ

 

Draws, cuts and pounces up to 12.75 inches (32.4 cm) high. Using the 
OMEGA system Panel feature, the GSx

plus

  can cut text or graphics in 

strips up to 96 feet (29.3 meters) long and 12.75 inches (32.4 cm) wide. 

ƒ

 

Adjustable tool force for uniform cutting with the turn of a dial. 

ƒ

 

Stepper motor drive for consistent performance and easy maintenance. 

ƒ

 

On-board 4K buffer in addition to OMEGA buffers. 

Содержание GSx Plus





























































Отзывы:

Нет отзывов