Gerber GSx Plus Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 60

Gerber GSx Plus Скачать руководство пользователя страница 41

40

Chapter 10:
Plotter Adjustments

This section contains a troubleshooting guide to help identify possible error
conditions according to the symptoms displayed and the recommended
adjustment procedures.

It also contains a brief description of plotter adjustment problems that should be
handled by contacting Gerber Field Service Department at 800-828-5406.

Note: Gerber warranties do not cover unauthorized repair. Some service
procedures require delicate adjustment of plotter parts. If damage to your
GSx

plus

plotter results from improper unauthorized service, repair will NOT be

covered by any Gerber warranty.

Troubleshooting Guide

This chart of symptoms is designed to help identify the possible problem and the
probable adjustment procedure.

CAUTION: Turn off GSx

plus

plotter and OMEGA or other sign

design system before checking connections or attempting to make
any adjustments, unless otherwise directed.

Symptom Recommended

Procedure

No power

1.

Check power cable and plugs.

2.

Check on/off switches.

3.

Check fuse.

Poor Performance Perform routine cleaning and lubrication.

Plotter Error

Press Reset on the plotter. Verify and resend the job.

Inconsistent Tool/
Material Contact

1.

Clean spindle bore and tool holder.

2.

Change knife blade.

3.

Check for proper Z home.

4.

Perform Z Axis Adjustment for Tool Height.

«
...
39
40
41
42
43
...
»

Содержание GSx Plus





























































Отзывы:

Нет отзывов