background image

REPLACEMENT PARTS

ELECTRICAL COMPONENTS:
(2) 

ELN-MX1540  (MICA HEATERS- 30” X 40” PRESSES)

(4)

ELN-MX1540  (MICA HEATERS- 40” X 64” PRESSES)

(1)

DKA-CTRLC  (PROCESSOR BOARD)

(1)

DKA-CTRLP  (POWER BOARD-220V)

(1)

ELN-BAYKTC10  (BAYONET THERMOCOUPLE SENSOR)

(1)

ELN-HVYLVR  (TABLE INDEX LEVER SWITCH)

(1) 

ELN-2CT01  (HEATER CONTACTOR-SINGLE PHASE MACHINES)

(1) 

ELN-4A064  (DPDT OCTAL TIMER RELAY)

(2) 

ELN-6HK58  (BLACK ACTIVATE PUSH BUTTON SWITCHES)

(1) 

ELN-6HK81  (RED EMERGENCY RELEASE PUSH BUTTON SWITCH)

AIR COMPONENTS:
(1) 

ARN-R184FO  (FRONT PANEL REGULATOR)

(1)

ARN-55B240   (AIR MAC VALVE)

(1) 

ARN-1B14365  (AIRBAG-30” X 40” PRESSES)

(2) 

ARN-1B14365  (AIRBAG-40” X 64” PRESSES)

(1) 

ARN-NAQ3KN03 (QUICK EXHAUST VALVE-30” X 40” PRESSES)

(2) 

ARN-NAQ3KN03  (QUICK EXHAUST VALVE-40” X 64” PRESSES)

(1) 

ARN-4ZJ86 (ADJUSTABLE EXH.FLOW CONTROL-30” X 40” PRESSES)

(2) 

ARN-4ZJ86 (ADJUSTABLE EXH.FLOW CONTROL-40” X 64” PRESSES)

MECHANICAL COMPONENTS:
SINGLE STATION TOP HEAT ONLY PRESSES
(2)

MEN-C930136D  (36” LOWER SIDE TABLE SLIDE-30” X 40” PRESSES)

(3) 

MEN-C930142D  (42” LOWER SIDE TABLE SLIDE-40” X 64” PRESSES)

RIGID TWIN STATION PRESSES
(6)

MEN-9546K18  (ADJUSTABLE STOP BUMPERS)

(8) 

MEN-NEO2WHL (NEOPRENE ROLLER WHEEL)

TOP & BOTTOM HEATED TWIN STATION PRESSES
(#)

MEN-T575S (STAINLESS STEEL TEFLON BLANKET SPRINGS)

(#)

MEN-¼20SPRACN  (SPRING ANCHOR STUD)

PRESS PADDING MATERIAL:
TOP HEAT ONLY PRESSES
(1) 

RMN-½NOM54YD  (1/2”NOMEX PAD -30” X 40” PRESSES)

(2) 

RMN-½NOM54YD  (1/2”NOMEX PAD –40” X 64” PRESSES)

TOP AND BOTTOM HEATED PRESSES
(1)

HCR-183040  (1/8” GREEN HCR RUBBER – 30” X 40” PRESSES)

(1)

HCR-184064  (1/8” GREEN HCR RUBBER – 40” X 64” PRESSES)

TWIN STATION TEFLON BLANKETS
(1) 

MAX-4064TFTS  (STITCHED BLACK TEF. BLANKET- 40” X 64” PRESSES)

Содержание Maxi Press Air














Отзывы: