Genie X-135/70 Скачать руководство пользователя страница 64

Страница: 64 / 71

Operator's Manual

First Edition • Seventh Printing

Transport and Lifting Instructions

62 ZX-135/70

Part No. 160567

Observe and Obey:



Only qualified riggers should rig the machine.



Only certified crane operators should lift the
machine and only in accordance with the
applicable crane regulations.



Be sure the crane capacity, loading surfaces
and straps or lines are sufficient to withstand
the machine weight. See the serial label for the
machine weight.

Lifting Instructions

Fully lower and retract the boom. Fully lower the jib.
Remove all loose items on the machine.

Determine the center of gravity of your machine
using the table and the picture on this page.

Attach the rigging only to the designated lifting
points on the machine. There are four lifting points
on the machine, one on each axle.

Adjust the rigging to prevent damage to the
machine and to keep the machine level.

Center of gravity

X Axis

Y Axis

ZX-1

5/70

72.75 in

1.85 m

40.5 in

1.03 m

Содержание X-135/70








































































Результаты поиска

Содержание X-135/70

Отзывы:

Похожие инструкции для X-135/70

Бренды по названию

Популярные бренды

Genie X-135/70, Руководство оператора

Результаты поиска

Содержание X-135/70

Отзывы:

Похожие инструкции для X-135/70

Бренды по названию

Популярные бренды