Genie X-135/70 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 71

background image

First Edition • Seventh Printing

Operator's Manual

Maintenance

Part No. 160567

ZX-135/70 65

Check the Engine Coolant Level –
Liquid Cooled Models

Maintaining the engine coolant at the proper level
is essential to engine service life. Improper coolant
level will affect the engine’s cooling capability and
damage engine components. Daily checks will
allow the inspector to identify changes in coolant
level that might indicate cooling system problems.

1

Check the coolant fluid level. Add fluid as
needed.

Result (Deutz TD2.9L engine): The fluid level
should be visible in the sight gauge on the
degas tank.

Result (all other engine models): The fluid
level should be in the NORMAL range.

Bodily Injury Hazard. Fluids in the radiator and
in the degas tank are under pressure and
extremely hot. Use caution when removing cap
and adding fluids.

Check the Batteries

Proper battery condition is essential to good
machine performance and operational safety.
Improper fluid levels or damaged cables and
connections can result in component damage and
hazardous conditions.

Electrocution hazard. Contact with hot or live
circuits may result in death or serious injury.
Remove all rings, watches and other jewelry.

Bodily injury hazard. Batteries contain acid.
Avoid spilling or contacting battery acid.
Neutralize battery acid spills with baking soda
and water.

1

Put on protective clothing and eye wear.

2

Be sure that the battery cable connections are
tight and free of corrosion.

3

Be sure that the battery hold-down brackets
are in place and secure.

Note: Adding terminal protectors and a corrosion
preventative sealant will help eliminate the
corrosion on the battery terminals and cables.

«
...
65
66
67
68
69
...
»

Содержание X-135/70








































































Отзывы:

Нет отзывов

Похожие инструкции для X-135/70

Бренд: Nelson Страницы: 18

Бренд: Nelson Страницы: 150

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: Balboa Страницы: 74

Бренд: GREER Company Страницы: 35

Бренд: ESAB Страницы: 34

Бренд: iWeld Страницы: 36

Бренд: Multi-Clean Страницы: 4

Бренд: Ravaglioli Страницы: 72

Бренд: M-system Страницы: 10

Бренд: Carel Страницы: 2

Millermatic 212

Бренд: Miller Electric Страницы: 44

Бренд: Interroll Страницы: 54

HERCULES 6.5 PLUS

Бренд: Fenix Страницы: 24

POWER i-MIG 200

Бренд: Everlast Страницы: 32

Бренд: CAME Страницы: 40

Бренд: WAGO Страницы: 50

Бренд: Worldwel Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды