Genie X-135/70 Скачать руководство пользователя страница 55

Страница: 55 / 71

First Edition • Seventh Printing

Operator's Manual

Operating

Instructions

Part No. 160567

ZX-135/70 53

Drive Enable

Light on indicates that the primary
boom has moved past either
circle-end wheel and the drive
function is turned off.

To drive, move the drive enable switch and slowly
move the drive/steer control handle off center.

If the drive/steer control handle is not moved within
two seconds of moving the drive enable switch, the
drive function will not operate. Release and move
the drive enable switch again.

Be aware that the machine may move in the
opposite direction that the drive and steer controls
are moved.

Always use the color-coded direction arrows on the
platform controls and the drive chassis to identify
the direction the machine will travel.

When the drive enable light is on, the axles cannot
retract.

Engine Idle Select (rpm)

Select the engine idle (rpm) by
pressing the engine idle select
switch. The indicator light next to
the current setting will be on.



Turtle symbol: low idle



Rabbit symbol: high idle

Check Engine Light

Light on and engine stopped: Tag the
machine and remove from service.

Light on and engine still running:
Contact service personnel within
24 hours.

Содержание X-135/70








































































Результаты поиска

Содержание X-135/70

Отзывы:

Похожие инструкции для X-135/70

Бренды по названию

Популярные бренды

Genie X-135/70, Руководство оператора

Результаты поиска

Содержание X-135/70

Отзывы:

Похожие инструкции для X-135/70

Бренды по названию

Популярные бренды