Genie X-135/70 Скачать руководство пользователя страница 10

Страница: 10 / 71

Operator's Manual

First Edition • Seventh Printing

General Safety

8 ZX-135/70

Part No. 160567

DANGER

Tip-over Hazard

Altering or disabling limit
switches can result in machine
tip-over. Machine tip-over will
result in death or serious injury.

DANGER

Do not alter or disable limit
switch(s).

31060 C

DANGER

Explosion / Burn Hazard
Ignition of explosive gases or contact with corrosive
acid will cause death, burns or blindness

31788 C

Keep all open flames and sparks away. Wear
personal protective equipment, including face
shield, gloves and long sleeve shirt.

READ MANUALS
Read all manuals prior to operation.

DO NOT OPERATE equipment if you do not
understand the information in the manuals.

Consult your supervisor, the owner or the
manufacturer.

Electrocution
Hazard
Contact with
energized
components can
result in death or
serious injury.

82237 B

DANGER

Avoid contact
with energized
components.

WARNING

Electrocution/Burn Hazard
Failure to di

connect all

the batterie

before

performin

g s

ervice on thi

machine may re

ult in

death or

eriou

injury.

connect

ll the

tterie

efore performing

ervice on

thi

chine.

WARNING

97865 B

Tip-over Hazard
Alterin

or di

ablin

can re

ult in machine tip-over.

Machine tip-over will re

ult in

death or

eriou

injury.

DANGER

Do not move,

lter or di

sab

ngle

or.

82314 B

31060

52865

97865

82314

114390

97875

31788

82237

114390

52865

97875

31788

1263543

97865

82237

31060

82314

229356 or 230977 or

1261816 or 1261817

Nut Torque

Dry bolts:

320 ft-lbs /
433.9 Nm

Foam-Filled Tire,
Minimum New
Wei

ht:

850 lbs / 386 kg

Tip-over Hazard

Failure to replace tire

with tire

ame

pecification will re

ult

in death or

eriou

injury.

Do not use air-filled tires.
Foam-filled tires are critical to
machine stability.

Do not replace factory-installed
tires with tires of different
specification or ply rating.

Tire Size
445D50/710, 18 ply Foam-filled

DANGER

1261816 A

229356 or 230977 or

1261816 or 1261817

229356 or 230977 or

1261816 or 1261817

1263543

Содержание X-135/70








































































Результаты поиска

Содержание X-135/70

Отзывы:

Похожие инструкции для X-135/70

Бренды по названию

Популярные бренды

Genie X-135/70, Руководство оператора

Результаты поиска

Содержание X-135/70

Отзывы:

Похожие инструкции для X-135/70

Бренды по названию

Популярные бренды