Genie X-135/70 Скачать руководство пользователя страница 63

Страница: 63 / 71

First Edition • Seventh Printing

Operator's Manual

Transport and Lifting Instructions

Part No. 160567

ZX-135/70 61

Securing to Truck or Trailer for
Transit

Always use the turntable rotation lock pin each
time the machine is transported.

Turntable rotation lock pin

Turn the key switch to the off position and remove
the key before transporting.

Inspect the entire machine for loose or unsecured
items.

Securing the Chassis

Use chains of ample load capacity.

Use a minimum of 6 chains.

Adjust the rigging to prevent damage to the chains.

Securing the Platform

Place a block under the platform rotator. Do not
allow the block to contact the platform cylinder.

Secure the platform with a nylon strap placed
through the lower platform support. Do not use
excessive downward force when securing the
boom section.

Содержание X-135/70








































































Результаты поиска

Содержание X-135/70

Отзывы:

Похожие инструкции для X-135/70

Бренды по названию

Популярные бренды

Genie X-135/70, Руководство оператора

Результаты поиска

Содержание X-135/70

Отзывы:

Похожие инструкции для X-135/70

Бренды по названию

Популярные бренды