Genesis LXP 200 Скачать руководство пользователя страница 2

Страница: 2 / 83

Genesis LXP

PREFACE

To ensure years of safe, dependable service, only trained and authorized persons should operate

and service the processor. It is the responsibility of the operator to read, fully understand and

follow all operational and safety-related instructions in this manual. Do not operate the processor

until you have read and fully understand these instructions. Always use good safety practices to

protect yourself and those around you.

IMPORTANT

THIS OPERATORS MANUAL MUST REMAIN WITH THE PROCESSOR AT ALL TIMES!

Should it become damaged or lost, immediately contact any authorized Genesis dealer or contact

the Genesis Service Department at 888-743-2748 or 715-395-5252 for replacement.

Genesis has made every effort to provide information as complete and accurate as possible for

its processors. However, because of owner requirements, equipment and control, variations may

exist. In addition, due to Genesis policy of continually striving to improve its products, occasional

discrepancies may exist between individual processors and the descriptions and information con-

tained herein.

Genesis reserves the right to make changes and improvements to its products at any time without

public notice or obligation. Genesis also reserves the right to discontinue manufacturing any

product at its discretion at any time.

REGISTRATION

The Warranty Registration Form must be filled out by the dealer or customer and returned to

Genesis indicating the date the machine went into service.

WARRANTY

All work or repairs to be considered for warranty reimbursement must be pre-authorized by the

Genesis Service Department. Any alterations, modifications or repairs performed before authoriza

tion by the Genesis Service Department wil render all warranty reimbursement consideration null

and void without exception. See page 63 for Warranty Claim Procedures.

A lack of, or improperly performed, maintenance and procedures as set forth in this manual as well

as operator abuse may render warranty consideration null and void.

Содержание LXP 200




















































































Результаты поиска

Содержание LXP 200

Отзывы:

Похожие инструкции для LXP 200

Бренды по названию

Популярные бренды

Genesis LXP 200, Инструкция по безопасности и эксплуатации

Результаты поиска

Содержание LXP 200

Отзывы:

Похожие инструкции для LXP 200

Бренды по названию

Популярные бренды