Genesis LXP 200 Скачать руководство пользователя страница 20

Страница: 20 / 83

Genesis LXP

OPERATION

Jaw set change-over requires at least one worker on the ground in addition to the operator. Use

basic safety precautions. All personnel on the ground must stand clear during operation.

Change-over Procedure:

Lower processor into stand. Lightly clamp jaw to middle plate.

Remove cylinder pins. Grease lock pin. Remove safety plates.

Retract cylinders.

•

While continuing to hold on processor cylinders retract lever (jaw open), hit electric switch

to retract lock pin.

•

Ensure both sides of lock pin have retracted. One side may fully retract before the other

begins to retract.

Articulate processor body to disengage jaw set.

Position processor body at new jaw set.

Check lock pin bores in new jaw set. Wipe bore clean to ensure there are no contaminants. Clean

quick plate trunion pins and mating “U” in processor body.

JAW SET CHANGE-OVER

Processor Body

Cylinder

Bore

Stand

Mating “U”

Cylinder

Quick Plates

Quick Plate Trunion

Содержание LXP 200




















































































Результаты поиска

Содержание LXP 200

Отзывы:

Похожие инструкции для LXP 200

Бренды по названию

Популярные бренды

Genesis LXP 200, Инструкция по безопасности и эксплуатации

Результаты поиска

Содержание LXP 200

Отзывы:

Похожие инструкции для LXP 200

Бренды по названию

Популярные бренды