Genesis LXP 200 Скачать руководство пользователя страница 35

Страница: 35 / 83

34 Genesis LXP

SHEAR JAW SET MAINTENANCE

PIERCING BLADES

1. Remove blades using an air-impact or breaker bar and

multiplier.

2. Remove dust and debris from blade seats; wipe down

with a rag and solvent.

3. Lightly file deformities from blade seat edges. Do not

sand or grind face of blade seats.

4. Install new, clean blades.

5. Snug lubricated blade bolts by hand to hold them in

place; push blades up-and-in to the upper and rear sur-

faces of the seats.

6. Torque bolts to 1/3 of the final torque value.

7. Check for firm contact against blade seats.

8. With a feeler gauge, confirm gap of .002” to .010” where

blades meet at piercing surface. A very narrow gap may

be confirmed by shining a flashlight from below the blades

and seeing light pass through.

If gap exceeds .010”, call the Genesis Service Department.

If no gap exists, remove blades, lightly grind facing sur-

faces, and repeat steps 5-8.

9. Torque bolts to 2/3 final value, and then to final value,

using a cross bolt pattern.

Piercing tip bolts must be lubricated and torqued as speci-

fied below. Correct clamping force is required to keep tips

from moving on their seats. Over-tightening can cause

bolt shanks to stretch, thus losing their clamping force.

Loose bolts will cause the seating areas to erode.

Replacement Procedure

Check gap

Model

Bolt size

Wet torque value

LXP 200

3/4”

282 Ft-lbs (383 Nm)

LXP 200

7/8”

455 Ft-lbs (617 Nm)

LXP 300/400/500

1.00”

675 Ft-lbs (916 Nm)

Содержание LXP 200




















































































Результаты поиска

Содержание LXP 200

Отзывы:

Похожие инструкции для LXP 200

Бренды по названию

Популярные бренды

Genesis LXP 200, Инструкция по безопасности и эксплуатации

Результаты поиска

Содержание LXP 200

Отзывы:

Похожие инструкции для LXP 200

Бренды по названию

Популярные бренды