Generic XOR 50 ccm Скачать руководство пользователя страница 99

Страница: 99 / 110

CHASSIS

Complaint

Symptom and possible causes

Remedy

Handling feels

too heavy.

Steering stem nut overtightened.
Broken bearing/race in steering

stem.

Distorted steering stem.
Not enough pressure in tires.

Adjust.
Replace.
Replace.
Adjust.

Wobbly
handle.

Loss of balance between right

and left front suspension.

Distorted front axle or crooked

tire.

Replace.

Replace.

Wobbly front

wheel.

Distorted wheel rim.
Worn front wheel bearings.
Defective or incorrect tire.
Loose nut on axle.
Loose nuts on the rear shock.
Worn engine mounting bushing.
Loose nuts or bolts for engine

mounting.

Replace.
Replace.
Replace.
Retighten.
Retighten.
Replace.
Tighten.

Front
suspension
too soft.

Weakened springs.
Oil leakage of shock absorber,

Replace.
Replace.

Front
suspension
too stiff.

Not enough grease,
Worn suspension arm spacer

Refill.
Replace.

Noisy front
suspension.

Not enough grease.
Loose nuts on suspension.

Refill.
Retighten.

Wobbly rear
wheel.

Distorted wheel rim.
Defective or incorrect tire.
Loose nuts on the rear shock

absorber.

Worn engine mounting bushing.
Loose nuts or bolts for engine

mounting.

Replace.
Replace.
Replace.
Replace.
Retighten.

Rear
suspension
too soft.

Weakened spring.
Oil leakage of rear shock

absorber.

Replace.
Add lubrication

Noisy rear
suspension.

Loose nuts on shock absorber,
lubrication leakage.

Adjust
Add lubrication.

Содержание XOR 50 ccm















































































































Результаты поиска

Содержание XOR 50 ccm

Отзывы:

Похожие инструкции для XOR 50 ccm

Бренды по названию

Популярные бренды

Generic XOR 50 ccm, Руководство по обслуживанию

Результаты поиска

Содержание XOR 50 ccm

Отзывы:

Похожие инструкции для XOR 50 ccm

Бренды по названию

Популярные бренды