Generic XOR 50 ccm Скачать руководство пользователя страница 98

Страница: 98 / 110

BATTERY

Complaint

Symptom and possible causes

Remedy

Battery runs

down
quickly.

The charging method is not

correct.

Cell plates have lost much of

their active material as a result of
over-charging.

A short-circuit condition exists

within the battery due to excessive
accumulation of sediments caused
by the incorrect electrolyte.

Battery is too old.

Check the magneto and regulator/rectifier
circuit connections, and make necessary
adjustments to obtain specified charging
operation.
Replace the battery, and correct the
charging system.

Replace the battery.

Replace the battery.

Reversed

battery
polarity.

The battery has been connected

the wrong way round in the system,
so that it is being charged in the
reverse direction.

Replace the battery and be sure to connect
the battery properly.

Battery

discharges
too rapidly.

Dirty container top and sides.
Battery is too old.

Clean.
Replace.

Содержание XOR 50 ccm















































































































Результаты поиска

Содержание XOR 50 ccm

Отзывы:

Похожие инструкции для XOR 50 ccm

Бренды по названию

Популярные бренды

Generic XOR 50 ccm, Руководство по обслуживанию

Результаты поиска

Содержание XOR 50 ccm

Отзывы:

Похожие инструкции для XOR 50 ccm

Бренды по названию

Популярные бренды