Generic XOR 50 ccm Скачать руководство пользователя страница 16

Страница: 16 / 110

NOTE

：

when bleeding the braking system, replenish the brake fluid reservoir if

necessary. Make sure that there is always some fluid visible in the reservoir.

Close the bleeder vavle, disconnect the pipe. Fill the reservoir with brake fluid to

the upper end of the inspection window.

BLEEDER VALVE

TIGHTENING TORQUE: 6-9N.m(0.6-0.9kg-m,4.5-6.5lb-ft)

CAUTION

：

Handle brake fluid with care: the fluid
reacts chemically with paint, plastics,

rubber materials, etc.

Rear brake

Turn adjusting nut so that the the play of the
brake lever is 15-25MM as shown in the
illustration.

Brake shoe wear

：

The vehicle is equipped with the brake
lining limit Indicator on the rear brake.
Inspect brake lining limit as follows

：

First check if the brake system is properly
adjusted.

when operating the brake, check to see

that the tip of indicator is within the range.

if the tip of indicator is beyond the range,

the brake shoe assembly should be
raplaced with anew set of shoe.

Содержание XOR 50 ccm















































































































Результаты поиска

Содержание XOR 50 ccm

Отзывы:

Похожие инструкции для XOR 50 ccm

Бренды по названию

Популярные бренды

Generic XOR 50 ccm, Руководство по обслуживанию

Результаты поиска

Содержание XOR 50 ccm

Отзывы:

Похожие инструкции для XOR 50 ccm

Бренды по названию

Популярные бренды