Generic XOR 50 ccm Скачать руководство пользователя страница 81

Страница: 81 / 110

BRAKE CALIPER REASSEMBLY

Reassemble and remount the calliper in the reverse

order of removal and disassembly, and also carry out
the following steps.
CAUTION:

Wash the calliper components with fresh brake fluid
before reassembly. Never use cleaning solvent or

gasoline to wash them.Apply brake fluid to the calliper
bore and piston to be inserted into the bore.

Reassemble and remount the calliper. (refer to preceding bove pages)

WARNING:

Bleed air after remounting the calliper. (refer to above pages)

MASTER CYLINDER REMOVAL AND DISASSEMBLY

Remove the handlebar cover. (Refer to above page)
Disconnect the front brake light switch lead wires.

Place a cloth underneath the union bolt on the master
cylinder to catch spilled drops of brake fluid. Unscrew

the union bolt and disconnect the brake hose master
cylinder joint.

CAUTION:

Completely wipe off any brake fluid adhering to any part of motorcycle. The fluid reacts

chemically with paint, plastics, rubber materials, etc.

Remove the master cylinder.

Содержание XOR 50 ccm















































































































Результаты поиска

Содержание XOR 50 ccm

Отзывы:

Похожие инструкции для XOR 50 ccm

Бренды по названию

Популярные бренды

Generic XOR 50 ccm, Руководство по обслуживанию

Результаты поиска

Содержание XOR 50 ccm

Отзывы:

Похожие инструкции для XOR 50 ccm

Бренды по названию

Популярные бренды