Gemini 810 Скачать руководство пользователя страница 39

Страница: 39 / 56

SERVICE AND TROUBLESHOOTING

CALIBRATION

WIRELESS INTERFERENCE

ALL OTHER CONDITIONS

The Gemini 810 + 980 diode laser uses solid-state circuitry to continuously monitor power output

and adjusts the power supplied to the laser diodes to maintain the output at the operator- defined

setting. If the output levels are more than ± 20% of the set value, the unit will shut off power to the

laser diode and provide an Error Message Alert to the operator.

If this happens, the unit should be turned off and allowed to sit for about five (5) minutes, then

turned on again. If the laser performs when re-tried, the microprocessor has been able to make

adjustments and the unit will function. If the unit fails to fire when re-tried, the device will need to

be sent for re-calibration by the manufacturer.
Re-calibration is recommended at a minimum of one time per year in order to maintain the required

accuracy of output power versus displayed power. The Gemini 810 + 980 diode laser may be returned

to the manufacturer for recalibration. Alternatively, a calibrated laser power meter, approved for use

with 810 nm-980 nm laser devices, may be purchased to check laser output power. The power meter

will also need to be calibrated at intervals recommended by the power meter manufacturer.
Laser output should be checked at 0.5, 1.0, 1.5 and 2.0 watts. The power meter display should be

within 20% of the meter reading. If not, replace the fiber tip. If the output is still outside the 20%

tolerance, the system must be returned to the manufacturer for re-calibration. The laser unit cannot

be re-calibrated by the user or service contractor and this must not be attempted.

This equipment has been tested and found to comply with the limits for Class B Digital Device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. This

equipment may cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on.

In the event that the Gemini 810 + 980 diode laser fails to operate correctly and your distributor

representative is unable to help, the system will need to be returned to the manufacturer for repair.

There are no user-repairable parts available for the device. It is recommended that the system be

returned in its original shipping box. If not available, one can be requested at the time you discuss

your service incident with your distributor representative.

Содержание 810

























































Результаты поиска

Содержание 810

Отзывы:

Похожие инструкции для 810

Бренды по названию

Популярные бренды

Gemini 810, Руководство пользователя

Результаты поиска

Содержание 810

Отзывы:

Похожие инструкции для 810

Бренды по названию

Популярные бренды