manualshive.com logo in svg

Gemini 810, Руководство пользователя

Поделиться
Скачать
Gemini 810 Скачать руководство пользователя страница 41

WHY DOES THE LASER STOP FIRING MID-PROCEDURE OR FAIL TO TURN ON?

 
CAUSE: 

1 - The laser diode is too hot and needs time to cool down before continued use.

 

 

2 - Output levels are more than ± 20% of the set value.

 

 

3 - Battery charge is too low to operate the laser.

 
SOLUTION:  1 - Allow 10-15 minutes for laser to cool down.
 

 

2 - Turn off the laser unit and wait 5 minutes, then turn the unit back on.  If the laser    

 

 

performs when re-tried, the microprocessor has been able to make adjustments and the  

 

 

unit will function properly. If the unit fails to fire when re-tried, the device will need to  

 

 

be sent for re-calibration by the manufacturer.

  

 

3 - Plug in the power adapter and let the laser unit charge for 60 minutes.  You can    

 

 

continue using the laser immediately after plugging in the external power.

WHY DOES THE LASER NOT FIRE WHEN I PRESS THE ACTIVATION PEDAL?

 
CAUSE: 

1 - Activation pedal not connected.

 

 

2 - Activation pedal AA Batteries are too low to operate.

 

 

3 - Laser is in Standby mode. 

 
SOLUTION:  1 - Check to see if the Bluetooth indicator on the activation pedal is on, and if    
 

 

there is a Bluetooth indicator on the top right of the display.  If either indicator is  

 

 

off, re-sync the footpedal by turning the laser unit off, waiting 10 seconds, and   

 

 

turning it back on.  Step on the activation pedal after a wavelength mode is selected  

  to 

re-sync.

 

 

2 - Replace the two AA batteries in the activation pedal.

 

 

3 - Touch the ACTIVE/STANDBY selection to activate the laser .

SERVICE AND TROUBLESHOOTING

I CAN HEAR THE LASER FIRING BUT IT IS CUTTING SLOWLY OR NOT CUTTING AT ALL

 

 
CAUSE: 

1 - Fiber tip is not initiated.

 

 

2 - Fiber tip is not in contact with tissue.

 

 

3 - Power setting is too low. 

 
SOLUTION:  1 -  The fiber tip should be initiated for any procedures where removal of tissue is  
  necessary.
 

 

2 - The fiber tip should be in contact with target tissues where removal of tissue is  

  necessary.
 

 

3 - The laser unit should be set at the proper power setting for the procedure.  The  

 

 

preset procedures are a good reference point.

41

Содержание 810

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды