gefran ADV200 SP Series Скачать руководство пользователя страница 67

Страница: 67 / 106

ADV200 SP • Quick start up guide - Specification and installation

Index Error message shown

on the display

Sub-code

Description

Error in motor connection.

Solution

:Check the motor connection, set the value of the direct current of the motor to 1/3 and

perform the motor autotune procedure. Then increase the direct current until autotuning is executed.
The penultimate value is the nominal current value at which the drive performs autotuning.

While running self-tuning the ESC key was pressed or the enable contact was opened or an alarm
occurred. The

Autotune

command was sent with the drive in the alarm condition

Solution

: Eliminate the reason for the alarm, remove the reason for the opening of the enable contact,

reset alarms.

A setting performed by the

Autotune

function produced a parameter value outside the min or max

range.

Solution

: Check the motor plate data or drive and motor sizes have been combined incorrectly.

The

Autotune

command was sent without being enabled.

Solution

: Close the enable contact before sending the

Autotune

command

Internal calculation error concerning IGBT control

Solution

: Perform autotuning once more, if the problem persists, contact the Gefran technical support

centre.

The drive has measured a stator resistance value exceeding the set limit.

Solution

: contact the Gefran technical support centre.

The drive has measured a stator resistance value below the set limit.

Solution

: contact the Gefran technical support centre.

11-12

Measurement of DTL internal compensation voltage outside accepted range.

Solution

: check connection between drive and motor.

If correct, the drive is faulty, contact the Gefran technical support centre.

13-14

Measurement of DTS internal voltage outside accepted range.

Solution

: check connection between drive and motor.

If correct, the drive is faulty, contact the Gefran technical support centre.

15 - 16 -17

LS leakage inductance value outside accepted range.

Solution

: Perform autotuning once more, if the problem persists, contact the Gefran technical support

centre.

18-19

Measurement of Im magnetising current outside accepted range.

Solution

: Perform autotuning once more, if the problem persists, contact the Gefran technical support

centre.

20-21

Measurement of Rr rotor resistor outside accepted range.

Solution

: Perform autotuning once more, if the problem persists, contact the Gefran technical support

centre.

Solution:

If the message appears with a value other than 0, follow the instructions supplied for each particular case

and repeat

Autotune

. This should be performed using the wizard function available from the keypad (STARTUP WIZ-

ARD) and the Tool software on the PC.
Pay attention to all motor plate data parmaeters, especially:
-

Rated speed

Motor rated speed

in rpm.

Rated frequency

Motor rated frequency

in Hz

Pole pairs

Motor pole pairs

Take care not to set the

Rated speed

parameter to the synchronous speed. The value of the

Rated speed

parameter

must be less than: [(

Rated frequency

* 60) /

Pole pairs

If the problem persists even after following the instructions supplied, confirm the values of the motor plate data
parameters, execute the

Take parameters

command but not

Autotune

Power config

Condition:

may occur during recognition of power cards. If this message is displayed, it is not possible to drive the

motor.

0020H-32

The power card is configured for a drive that is incompatible with the regulation card

0021H-33

The configuration of the power card is not compatible with the regulation card

Содержание ADV200 SP Series











































































































Результаты поиска

Содержание ADV200 SP Series

Отзывы:

Похожие инструкции для ADV200 SP Series

Бренды по названию

Популярные бренды

gefran ADV200 SP Series, Быстрый старт, технические характеристики и установка

Результаты поиска

Содержание ADV200 SP Series

Отзывы:

Похожие инструкции для ADV200 SP Series

Бренды по названию

Популярные бренды