Gefen EXT-UHDV-KA-LANS-RX Скачать руководство пользователя страница 8

Страница: 8 / 188

viii

Features and Packing List

Features

•

Secure content distribution using AES-128 bit encryption

•

Extends HDMI, VGA, USB, RS-232, bi-directional stereo analog audio, and IR over IP,

using a Gigabit Local Area Network

•

Supports input resolutions up to 4K 60Hz 4:2:0 on HDMI and up to 1920x1200, 60 Hz

on VGA (WUXGA).

•

Supports output resolutions up to 4K 30Hz 4:4:4 on HDMI and up to 1920x1200 60 Hz

or 1080p Full HD on VGA

•

Supported HDMI Features:
►

HDR

►

HDCP 2.2 and 1.4

►

Deep Color

► Lip-Sync pass-through

•

Supports uncompressed LPCM digital audio up to 7.1 channels

•

Supports up to 7.1 channels of HBR (High Bit Rate) digital audio including Dolby

Atmos®, Dolby® TrueHD, DTS:X™, and DTS-HD Master Audio™

•

When used with Gefen DVI-to-HDMI cables (not included), supports the use of DVI

sources and DVI displays up to 1080p Full HD and 1920x1200 (WUXGA)

•

Built-in video wall controller accommodates any number of rows and columns up to

16x16

•

Digital and analog audio break-out allows audio to be de-embedded from the HDMI

output of the Receiver and be sent to a separate audio system, enhancing the impact

of AV presentations.

•

Quick mass-firmware-update, automated configuration, and enhanced control

capabilities and system security when used with the Gefen EXT-CU-LAN Matrix

Controller

•

Built-in web interface, Telnet, and UDP

•

Compatible with the Gefen Keyboard Switching Controller software, available for

download at www.gefen.com

•

Supports 39,900 Senders and a combination of just over 65,000 Sender and Receiver

units, depending on the network bandwidth and number of ports on your network

switch

•

Two USB 2.0 ports with data rates up to 480 Mbps and backward-compatibility with

USB 1.1

•

Two USB 1.1 ports for use with Human Interface Devices (H.I.D.)

•

Conforms to IEEE 802.3af PoE standard

•

PoE (Power over Ethernet) allows the new Sender and Receiver units to be powered

through a standard PoE-enabled IP network switch, without the need for external

power supplies

•

Three-port Gigabit Ethernet switch built into the Receiver unit

•

Mode switch on Sender for sharpness or motion optimization of image

Содержание EXT-UHDV-KA-LANS-RX





























































































































































































Результаты поиска

Содержание EXT-UHDV-KA-LANS-RX

Отзывы:

Gefen EXT-UHDV-KA-LANS-RX, Руководство пользователя, Страница: 8 / 188

Результаты поиска

Содержание EXT-UHDV-KA-LANS-RX

Отзывы: