Gefen EXT-UHDV-KA-LANS-RX Скачать руководство пользователя страница 5

Страница: 5 / 188

Operating Notes

•

Always make sure that the 4K Ultra HD HDMI & VGA KVM over IP is running the

latest firmware.

•

Gefen highly recommends the use of the Syner-G software and Matrix Controller

(Gefen part no. EXT-CU-LAN) for setting up and controlling the operation of a

Video-over-IP network using these products.

•

Shielded CAT-5e (or better) cables should not exceed 330 feet (100 meters) between

the Sender / Receiver unit and the network.

•

By default, all Sender and Receiver units are set to channel 0.

•

The HDMI inputs and outputs on this product also support Single-Link DVI and its

standard VESA resolutions. Dual-Link DVI is not supported.

•

Only the HDMI Input and Output will pass content from HDCP sources such as Blu-ray

players and PlayStation® console systems. VGA does not support HDCP content. If

HDCP encrypted content is being passed, the VGA output will not be active.

•

By default, the source device will use the EDID from the display (or other sink device)

which is connected the Receiver unit.

•

terminating network cables in the field, please adhere to the TIA/EIA568B

specification. See the

Network Cable Diagram (page 172

)

for details.

•

Supported USB Devices

► HID-class devices: keyboard, mouse, joystick, and touch panels.
► Bulk-only storage devices: USB flash drive, most storage devices, DVD-ROM,

card readers, and printers.

Important

•

When connecting through a Local Area Network, a managed gigabit

switch is required. Jumbo Frame Support (8k or greater) and IGMP

Snooping must be enabled.

•

A dedicated LAN is not required but highly recommended.

•

When using HDCP-encrypted content, only the HDMI inputs and outputs

can accept and display the content.

•

We recommend that Sender and Receiver are first connected directly

and functionality/performance is fully verified before integrating them into

a Local Area Network.

Important

This product has been specifically designed for use with the Gefen Syner-G™

Software Suite, available for download at www.gefen.com. The Gefen

Syner-G™ Discovery and Show-Me features simplify initial IP configuration

Содержание EXT-UHDV-KA-LANS-RX





























































































































































































Результаты поиска

Содержание EXT-UHDV-KA-LANS-RX

Отзывы:

Gefen EXT-UHDV-KA-LANS-RX, Руководство пользователя, Страница: 5 / 188

Результаты поиска

Содержание EXT-UHDV-KA-LANS-RX

Отзывы: