Gefen EXT-UHDV-KA-LANS-RX Скачать руководство пользователя страница 14

Страница: 14 / 188

page | 2

Sender Unit

Introduction

tting S

tar

ted

tting S

tar

ted

Name

Description

Power

This LED glows solid blue when the unit is

connected to an AC outlet and the unit is

powered ON. See

LED Status (page

)

for more information.

Link

This LED glows solid green when the Sender

unit and Receiver unit are connected and

passing video. See

LED Status (page

)

for more information.

RS-232

Connect an RS-232 cable from this port to an

RS-232 controller. See

Using RS-232 (page

)

for more information.

Prog Sel

For factory use only. This switch

must

stay

in the Off position.

IR Out

Connect an IR Emitter cable (Gefen part no.

EXT-IREMIT) from this port to the UHD/HD

source to control the source from the viewing

location.

IR In/Ext

Connect an IR Extender (Gefen part no.

EXT-RMT-EXTIRN) to this

3.5mm mini-

stereo port. Alternatively, connect a 3.5mm

mini-stereo connector from this port to the

output of an automation system with an

electrical IR output.

Prog

For factory use only.

Power

RS-232

Off On
Prog Sel IR Out

IR In/Ext

Prog Reset

VGA Out

Link

4K Ultra HD HDMI & VGA KVM over IP S

EXT-UHDV-KA-LANS-TX

5V DC

USB

LAN (PoE)

VGA In

HDMI In

Line In

Line Out

Содержание EXT-UHDV-KA-LANS-RX





























































































































































































Результаты поиска

Содержание EXT-UHDV-KA-LANS-RX

Отзывы:

Gefen EXT-UHDV-KA-LANS-RX, Руководство пользователя, Страница: 14 / 188

Результаты поиска

Содержание EXT-UHDV-KA-LANS-RX

Отзывы: