Gefen EXT-UHDV-KA-LANS-RX Скачать руководство пользователя страница 24

Страница: 24 / 188

page | 12

Using a Direct Connection

By default, the 4K Ultra HD HDMI & VGA KVM over IP is shipped in

Auto IP

mode.

Auto IP

mode is used for directly connecting Sender and Receiver units to one another. In

Auto IP

mode each Sender and Receiver unit assigns itself a unique IP address within the range of

169.254.x.x

. To configure the units to work over a LAN, we must access the

Web interface of the Sender and Receiver unit on a computer. Then, we can change

the network settings.

Connect an HDMI cable to connect the UHD/HD source to the

HDMI In

port on the

Sender unit.

Connect an HDMI cable from the UHD/HD display to the

HDMI Out

port on the Re-

ceiver unit.

Connect a shielded CAT-5e (or better) cable from the

LAN (PoE)

port on the Sender

unit to the

LAN 3 (PoE)

port on the Receiver unit. While any of the three ports on the

Receiver can be used, we recommend using

LAN 3 (PoE)

for the sake of consistency.

Connect another shielded CAT-5e (or better) cable from one of the

LAN

ports on the

Receiver unit to a PC.

5. C

onnect the included 5V DC locking power supplies to both the Sender unit and

Receiver unit. Do not overtighten the locking connectors. Connect the included AC

power cords from the power supplies to available electrical outlets.

Obtain the IP address of both the Sender and Receiver unit by disconnecting the

HDMI cable from the Sender unit (or from the source device). Information, similar to

the illustration on the next page, will be displayed.

Power

RS-232

Off On
Prog Sel IR Out

IR In/Ext

Prog Reset

VGA Out

Link

4K Ultra HD HDMI & VGA KVM over IP S

EXT-UHDV-KA-LANS-TX

5V DC

USB

LAN (PoE)

VGA In

HDMI In

Line In

Line Out

EXT-UHDV-KA-LANS-RX

Line In Line Out Opt Out

HDMI Out

VGA Out

Prog

3 (POE)

5V DC

LAN

Power

Link

USB2.0

USB1.1

Reset VGA

USB

IR In/Ext

IR Out

On Off

Prog Sel

RS-232

HDMI

USB

tting S

tar

ted

Installation & Configuration

Sender unit

Receiver unit

Connect to PC

tting S

tar

ted

Содержание EXT-UHDV-KA-LANS-RX





























































































































































































Результаты поиска

Содержание EXT-UHDV-KA-LANS-RX

Отзывы:

Gefen EXT-UHDV-KA-LANS-RX, Руководство пользователя, Страница: 24 / 188

Результаты поиска

Содержание EXT-UHDV-KA-LANS-RX

Отзывы: