Gefen EXT-UHDV-KA-LANS-RX Скачать руководство пользователя страница 25

Страница: 25 / 188

page | 13

tting S

tar

ted

Installation & Configuration

Make note of both IP addresses. These IP addresses can be entered in a Web

browser to access the built-in Web interface.

See

Local Area Network (LAN) Connection (page

)

and follow steps 6 - 22,

in order to configure your PC and access the built-in Web interface.

Set the video channel. By default, both the Sender and Receiver unit are set

to channel 0. See

Setting the Video Channel (page

)

for more information.

10.

Once both Sender and Receiver units are configured using the built-in Web

interface, the shielded CAT-5e cable, between the PC and the Receiver unit,

can be disconnected.

11.

See

Supplementary Connections (page

)

for instructions on connecting USB,

IR, RS-232, and audio cables.

Waiting for video source - standby

FW: V1.53H-Oct-24 779c

Local IP: 169.254.7.231

Remote IP: 169.254.6.250

ID: 001C9103C003

Local IP = Receiver unit

Remote IP = Sender unit

Содержание EXT-UHDV-KA-LANS-RX





























































































































































































Результаты поиска

Содержание EXT-UHDV-KA-LANS-RX

Отзывы:

Gefen EXT-UHDV-KA-LANS-RX, Руководство пользователя, Страница: 25 / 188

Результаты поиска

Содержание EXT-UHDV-KA-LANS-RX

Отзывы: