manualshive.com logo in svg

GE Profile PT920, Техническое обслуживание руководство, Страница: 38 / 47

Поделиться
Скачать
GE Profile PT920 Скачать руководство пользователя страница 38

– 38 –

Oven Sensor and Door Switch Test

Note

: See 

Lock Assembly

 for door switch function explanation. 

Remove power from oven. 

1. 

Make resistance measurement from side of sensor and lock switch connector with exposed terminals.

2. 

The resistance measurements are made on the logic board at the connector listed on the chart below.

3. 

If abnormal reading is observed, wiggle leads at disconnect block. If any variation occurs, replace. 

4. 

Resistance Measurement Chart

Models

Circuit

Connector

Terminals

Ohms

PT920 
and 
PT960 
Upper Oven

Oven Sensor

J3

9 to 10

1091 

Ω

 @ Rm. Temp.

1654 

Ω

 @ 350°F

2634 

Ω

 @ 865°F

Door Latched

J3

5 to 6
4 to 6

0 

Ω

 

open

Door Unlatched

J3

4 to 6
5 to 6

0 

Ω

 

open

PT960 
Lower Oven 
Only

Oven Sensor

J2

9 to 10

1091 

Ω

 @ Rm. Temp.

1654 

Ω

 @ 350°F

2634 

Ω

 @ 865°F

Door Latched

J2

4 to 5
3 to 5

0 

Ω

 

open

Door Unlatched

J2

3 to 5
4 to 5

0 

Ω

 

open

1

2

3

4

5

6

7

8

9

10

MEAT PROBE

30K-50K 

Ω

 @

ROOM TEMP.

OVEN

SENSOR

DOOR

UNLOCKED

DOOR

CLOSED

DOOR

LOCKED

1

2

3

4

5

6

7

8

9

10

11

MEAT PROBE

30K-50K 

Ω

 @

ROOM TEMP.

OVEN

SENSOR

DOOR

UNLOCKED

DOOR

CLOSED

DOOR

LOCKED

Single and Upper Oven

Lower Oven

J2

J3

BAKE FAD 

BAKE FAD 

THERMAL 

THERMAL 

SWITCH

SWITCH

BAKE FAD 

BAKE FAD 

THERMAL 

THERMAL 

SWITCH

SWITCH

Содержание Profile PT920
















































Отзывы:

Нет отзывов