GE Profile PT920 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 47

– 28 –

Caution

: It is possible to reconnect the switch wiring

incorrectly to the lock assembly. When reconnecting
the wiring, make sure it is properly connected to the
lock assembly before turning the power back on.

To remove the lock assembly on lower double
ovens:

Access the lower control compartment. (See

1.

Lower Oven Control Compartment Access

.)

2. Open lower oven door.

3. Remove 2 Phillips-head screws from the door

lock assembly.

Mark and disconnect connectors from the lock

4.

assembly.

Remove 2 hex-head screws and the lock

5.

assembly from the oven.

Lock Assembly

4. Mark and disconnect connectors from the lock

assembly.

Caution

: It is possible to reconnect the switch wiring

incorrectly to the lock assembly. When reconnecting
the wiring, make sure it is properly connected to the
lock assembly before turning the power back on.

Door Lock - Unlocked Position

Strip Circuit

To remove the lock assembly on single and upper
double ovens:

Access the control compartment. (See

1.

Control

Compartment Access

.)

Hold control panel and open oven door.

2.

Place the control panel on a protected oven

3.

door as shown.

LOW TEMP

THERMAL SW

O

Y

Y

BU

BU

4

5

6

LOCK SW

UNLOCK SW

UNLOCKED

«
...
26
27
28
29
30
...
»

Содержание Profile PT920
















































Отзывы:

Нет отзывов