GE Profile PT920 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 47

– 27 –

Lock Assembly

The motorized door lock assembly is located above
the oven. The assembly consists of a lock motor
cam and switch assembly, lock hook, mounting
plate, door switch, spring, and plunger.

The lock motor is energized when the control is set
for Clean and Clean Time is selected. The K9 relay
contact will close and complete the circuit that
supplies the voltage to the lock motor.

The lock motor has approximate resistance value of
1.9K

Ω

.

Note:

To enable proper operation of the door lock,

•

ensure that the door jamb switch is in “common”
to “normally closed” (door closed). This enables
power to be delivered when the door lock closes.

Display of control will

fl

ash

•

“LOCKED”

if the door

switch is in the “C" (common) to “NC” (normally
open) position (door open).

The word

•

“LOCKED”

will

fl

ash on and off in the

display while the lock motor is in motion. When
the door is locked, the word

“LOCKED”

remains

illuminated in the display.

Door Locking/Unlocking Strip Circuit

The cam on the motor performs two functions:

Positions the lock hook in the door to prevent

1.

opening during clean operation.

Operates the lock switches, which signal the

2.

control if the door is unlocked or locked and
ready for clean operation.

Note:

When door is either being locked or unlocked,

both the lock and unlock switches will be in the open
position. The locked and unlocked diagrams are
representative of a single/upper oven but apply also
to a lower oven.

Door Lock - Locked Position

Motor

Door

Switch

Hook

Plunger

Unlock Switch

Lock Switch

Strip Circuit

LOW TEMP

THERMAL SW

O

Y

Y

BU

BU

4

5

6

LOCK SW

UNLOCK SW

LOCKED

CIRCUIT

TERMINALS

OHMS

Oven Sensor

9 to 10

1091

Ω

@ Rm Temp.

1654

Ω

@ 350°F

2634

Ω

@ 865°F

Door Latched 5 to 6

0

Ω

4 to 6

open

Door Unlatched 4 to 6

0

Ω

5 to 6

open

SINGLE/UPPER OVEN

CIRCUIT

TERMINALS

OHMS

Oven Sensor

9 to 10

1091

Ω

@ Rm Temp.

1654

Ω

@ 350°F

2634

Ω

@ 865°F

Door Latched 4 to 5

0

Ω

3 to 5

open

Door Unlatched 3 to 5

0

Ω

4 to 5

open

LOWER OVEN (Double Wall Oven Only)

(

Continued Next Page

)

C

LOCK RELAY

LOCK

MOTOR

MDL

N

L

K9

«
...
25
26
27
28
29
...
»

Содержание Profile PT920
















































Отзывы:

Нет отзывов