GE Profile PT920 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 47

– 31 –

Meat Probe and Outlet

If equipped, the meat probe outlet is located on
the top of the oven cavity, near the front. The meat
probe outlet is connected to the electronic oven
control. The meat probe has a resistance value of
30K-50K

Ω

at room temperature.

To remove the meat probe outlet:

Open the oven door.

1.

Remove the two

2.

1

/

4

-in. hex-head screws that

hold the meat probe outlet to the top of the oven
cavity.

Remove the control panel (see

3.

Control

Compartment Access

) and disconnect the meat

probe connector.

Pull the probe outlet wiring through the meat

4.

probe outlet.

Note:

Upon reassembly, ensure displaced insulation

around oven and components is returned to its
original position.

Meat Probe Outlet

Bake Element

Note:

The resistance of this component can be

tested from the EOC. (See

Control Board Testing

.)

The element is rated at 2100 watts, has an
approximate resistance value of 27

Ω

, and draws

approximately 8.5 amps.

The bake element is located under the oven

fl

oor.

Bake element terminals are located behind the rear
access panels on both the single and double wall
ovens.

To remove a bake element:

Remove the oven from the installation. (See

1.

Oven

Removal

.)

Remove the left side access panel for the

2.

appropriate bake element. (See

Side Access

Panels

.)

Carefully lift the insulation from the outside of

3.

the oven to access the screws that hold the
bake element cover in place.

Remove two ¼-in hex-head screws and the

4.

bake element cover from oven.

Remove 1/4-in. hex-head screws and bake

5.

element terminal cover from oven.

Disconnect the wires from the bake element.

6.

Bake Element Cover

(

Continued Next Page

)

«
...
29
30
31
32
33
...
»

Содержание Profile PT920
















































Отзывы:

Нет отзывов