GE Profile PT920 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 47

– 32 –

Cooling Fan

A cooling fan is controlled by the logic board and
is located above each oven. On upper and single
ovens, the cooling fan is in the rear wall on the left
side of the control compartment. On lower ovens,
the cooling fan is located on the right side of the
back wall in the lower control compartment. On
double ovens, both fans operate together.

The fans will begin to operate when the oven is
in any cooking mode. The fans may continue to
operate even after the oven is turned off.

The fan motor in the single or upper oven, and the
fan motor in the lower oven is a 2-speed motor. Fan
speed is controlled by the microswitch on the door
lock: Locked = high speed and unlocked = low speed.
The cooling fans have the following approximate
resistance values:

Single or

Upper Oven

Lower Oven

White/red to

white/black

13

Ω

10

Ω

Black to

white/black

18

Ω

21

Ω

White/red to

black

30.7

Ω

31

Ω

Access to the single and upper oven cooling fans
and the lower oven cooling fan require the oven to
be removed.

To remove the cooling fan in the single and upper
oven:

Remove the oven from the installation. (See

1.

Oven

Removal

.)

Remove the top access panels. (See

2.

Top Access

Panels

.)

Disconnect the cooling fan wire harness.

3.

Cooling Fan Wire Harness

Carefully move the insulation to access and

7.

remove the two 1/4-in hex-head screws (one
on each side of terminals) that hold the bake
element to the oven.

8. Grasp and pull the element out from the left side

of the oven by moving the element to the front
of the oven to clear the terminal ends.

Note:

Upon reassembly, ensure displaced insulation

around oven and components is returned to its
original position.

Disconnect

(

Continued Next Page

)

«
...
30
31
32
33
34
...
»

Содержание Profile PT920
















































Отзывы:

Нет отзывов