GE NetworX NX-6, Установка и запуск

Страница: 14 / 48

Page 12
FEATURE SELECTION DATA
Feature selection data will display the current condition (on or off) of eight features associated with the programming
location and segment selected. Pressing a button on the touchpad (1 thru 8) that corresponds to the "feature number"
within a segment will toggle (on/off) that feature. Pressing any numeric key between [
1 ] and [ 8 ] for selection of a
feature, will make the corresponding LED illuminate (feature ON). Press the number again, and the LED will extinguish
(feature OFF). You will see that numerous features can be selected from within one segment. For instance, if all eight
features of a segment are desired, pressing [
1 ]-[ 2 ]-[ 3 ]-[ 4 ]-[ 5 ]-[ 6 ]-[ 7 ]-[ 8 ] will turn on LED's 1 thru 8 as you press the
keys, indicating that those features are enabled. LCD Keypad Users Note: The numbers of the enabled features
will be displayed. However, the features not enabled will display a hyphen (-). After the desired setting of
features is selected for this segment, press the [
r
] key. This will enter the data and automatically advance to the next
segment of the location. When you are in the last segment of a location and press the [
r
] to enter the data, you will exit
that location. This will now turn the "Ready" LED off and the "Armed" LED on. As before, you are now ready to enter
another programming location.
LOADING FACTORY DEFAULTS
To load the factory defaults, enter the program mode using the procedure on page 10, then type [ 9 ]-[ 1 ]-[ 0 ]-[ # ]. The
keypad will beep 3 times indicating that the loading is in progress. The loading takes about 6 seconds.
ENROLLING MODULES AND KEYPADS
For supervision purposes, the NX-6 has the ability to automatically find and store in its memory, the presence of all
keypads, zone expanders, wireless receivers, and any other module connected to the data terminal. This allows these
modules to be supervised by the control panel. To enroll the modules, enter the Program Mode of the NX-6 control panel
as described on page 10. When the Program Mode is exited, the NX-6 control will automatically enroll the devices. The
enrolling process takes about 12 seconds, during which time the "Service" LED will illuminate. User codes will not be
accepted during the enrolling process. If a speaker is attached to the NX-6, it will click at this time. If a siren or bell is
attached to the NX-6, it will sound for about 1 second. Once a module is enrolled, if it is not detected by the control, the
"Service" LED will illuminate.
CONTROL PANEL PROGRAMMING LOCATIONS
(Various locations intentionally omitted. Attempts to access these reserved locations will cause the
keypad to sound an error beep.)
LOCATION 0
PROGRAMMING PHONE #1
20 segments, numerical data
The first telephone number is programmed in location 0. A "14" indicates the end of the phone number. Delays of 4
seconds can be programmed at any point in the phone number by programming a "13" in the appropriate segment. If
tone dialing is desired, program a "15" in the segment where tone dialing should begin. If the entire number should be
tone dialing, program a "15" in the first segment. Program an
A
11" for a
A r @
, and a
A
12" for a
A
#
@
. Caution : A call-waiting
cancel on a non- call waiting line will prevent successful connection to the central station.
LOCATION 1 ACCOUNT CODE FOR THE PHONE #1
6 segments, numerical data
The account code sent when Phone #1 is dialed is programmed in location 1. Program a
A
10" in the segment immediately
after the last digit of the account code. If the account code is 6 digits long, program all 6 segments.
LOCATION 2 COMMUNICATOR FORMAT FOR PHONE #1
1 segment, numerical data
Location 2 contains the communicator format used to transmit to the receiver connected to Phone #1. Consult the
instructions for your central station receiver to determine which format is compatible. Select a format from the list on
the following page. If you require a format other than those listed, review the override options described in location 18,
to build the appropriate format. A "15" must be programmed in location 2 in addition to the entries in location 18 in
order to create a special format. If this location contains a "0", the built-in communicator will be disabled, and the NX-6
will function as a local only control.