CHAPTER 3: IEC 61850 COMMUNICATION
MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
UR FAMILY – COMMUNICATIONS GUIDE
3-219
3
PhDir1
SPS
Indicates Phase Comparison of differential is satisfied per phase, where the last
digit of instance number 1, 2, or 3 refers to phase A, B, and C respectively.
The BUS 1 DIR A/B/C operand.
The STATOR DIFF1 DIR A/B/C operand.
B_DifPDIF, BusDifPDIF,
SttDifPDIF
PhsAInd
SPS
An LED.
The LED PHASE A operand.
LEDsIHMI
PhsBInd
SPS
An LED.
The LED PHASE B operand.
LEDsIHMI
PhsCInd
SPS
An LED.
The LED PHASE C operand.
LEDsIHMI
PlOpn
ACT
Open pole detector is operated.
The OPEN POLE OP operand.
OpnPl
Θ
SCBR
PosTotVArh
MV
SRC 1 Total VAr-hour in positive direction
EnrMtrMMTR
PosTotWh
MV
SRC 1 Total Watt-hour in positive direction
EnrMtrMMTR
ProcBusFail
SPS
Process bus system status.
The PROCESS BUS FAILURE operand.
LPHD
ProcBusTrbl
SPS
Process bus trouble.
The PROCESS BUS TROUBLE operand.
LPHD
ProjectedDif
MV
Phase angle difference between V1 and projected V2 (V2').
SYNCHROCHECK 1 DELTA PHASE', in degrees which is the phase angle difference
between V1 and projected V2.
SynChkRSYN
ProjectedV1
CMV
Projected V2 Voltage phasor.
SYNCHROCHECK 1 V2' voltage phasor, in primary volts.
SynChkRSYN
PtpFail
SPS
Bad PTP Signal.
The PTP FAILURE operand.
LPHD
Raise
SPS
PID 1 RAISE operand value
PIDRegFPID
RawAnsp
MV
Raw neutral split phase current. Raw INsp in per unit.
NeAUnPTOC
RawAPh
WYE
Raw Id in per unit for Phase A, B, and C
PhAUnPTOC
RecBlk
SPS
Manually block autoreclose.
The BREAKER 1 BLK RCLS operand.
Bkr0XCBR
RecEna
SPS
Manually enable autoreclose.
The BREAKER 1 ENA RCLS operand.
Bkr0XCBR
RefWinding
INS
Reference winding. Number of windings used as the reference winding for ratio
compensation.
PctDifPDIF
RelDpo
SPS
This data object indicates that not all criteria are fulfilled, and the switching/
operation action is not released to proceed. Complement of Rel.
The SYNC 1 CLS DPO operand, which becomes Off when all synchrocheck criteria
are fulfilled.
SynChkRSYN
RemCmdAcsOff SPS
Indicates operations of FlexLogic operand ACCESS REM CMND OFF
SecGSAL
RemCmdAcsOn SPS
Indicates operations of FlexLogic operand ACCESS REM CMND ON
SecGSAL
RemMod
SPS
Capacitor control in remote mode.
The CAP 1 IN REMOTE operand.
CapCtlGAPC
RemSetAcsOff
SPS
Indicates operations of FlexLogic operand ACCESS REM SETG OFF
SecGSAL
RemSetAcsOn
SPS
Indicates operations of FlexLogic operand ACCESS REM SETG ON
SecGSAL
RemUnA
SPS
Indicates remote open pole condition is detected in phase A, B, or C.
The OPEN POLE REM OP phase A/B/C operand.
OpnPl
Θ
SCBR
ReSigma
SPC
Command for the Hi-Z Sigma Value Reset
HiZPHIZ
Restart
SPS
Indicates the motor has restarted.
The MOTOR RESTART operand.
MotThmPTTR
RgDstIP
VSG
Expected value of Destination IP address field in messages subscribed to by
RxGOOSE#. The multicast IP address of subscribed R-GOOSE message.
LGOS
RgRxMode
ENG
R-RxGOOSE1 Reception Mode setting: 0 = Unicast, 1 = SSM; 2=ASM
LGOS
RgSrcIP
VSG
Expected value of Source IP address field in messages subscribed to by
RxGOOSE#. The source IP address of subscribed R-GOOSE message.
LGOS
Data object
name
CDC
Semantics
Used in logical nodes…