GE AIR C18 Скачать руководство пользователя страница 52

Страница: 52 / 60

—

⑧

Installing Front Panel

1. As shown in Figure 4, align the position of the guide louver motor at the front panel with the position of the pipe outlet

of the indoor unit.

2. Installing Front Panel

①

Install the front panel to the indoor unit temporarily. When installing, hang the clasp on the hook of the indoor unit

opposite the position of the guide louver motor at the front panel (two positions).

②

Temporarily hang the remaining two clasps on the main hook (pay attention not to entangle the cable of the guide

louver motor in the sealing materials).

③

Drive the four hexagon screws below the clasp in about 15 mm (The front panel shall ascend).

④

As shown in the figure, adjust the front panel to the direction of the arrow, so that the adjusting plate engages with

the ceiling well.

⑤

Tighten the screws until the thickness of the sealing materials between the front panel and the indoor unit is

decreased to 5-8mm.

(Figure 4)

Clasp

Hook

Pipe Opening Position

Guide Louver Motor

Indoor Unit

Ceiling

Sealing Materials

5mm to 8mm

Air Outlet

Decorative Front Panel

Содержание AIR C18





























































Результаты поиска

Содержание AIR C18

Отзывы:

Похожие инструкции для AIR C18

Бренды по названию

Популярные бренды

GE AIR C18, Руководство по установке

Результаты поиска

Содержание AIR C18

Отзывы:

Похожие инструкции для AIR C18

Бренды по названию

Популярные бренды