GE AIR C18 Скачать руководство пользователя страница 49

Страница: 49 / 60

—

⑤

Drainage Pipe

1 Installing Drainage Pipe

●

The diameter of drainage pipe shall be equal to or larger than the diameter of the connecting pipe (size of

polyethylene pipe : outer diameter 25mm, wall

≥①

1.5mm)

●

The drainage pipe shall be short, with a declining slop as at least 1/100, so as to avoid the forming of gaseous

envelope.

●

In case it is impossible to have enough slope for the flexible drainage pipe, install a drainage lift pipe.

●

To avoid bending of the flexible drainage pipe, the distance between the two suspenders shall be 1 to 1.5m.

(Correct) Slope more than 1/100 (Wrong)

●

Use the flexible drainage pipe

①

and the clamp

②

supplied as accessories with the unit

●

Insert the flexible drainage pipe into the drainage faucet, and then tighten the clamp

②

●

Use the big sponge

⑩

to wrap the clamp at the flexible drainage clamp for thermal insulation.

●

Take thermal insulation measures for the indoor flexible drainage pipe.

2 Precautions for Installing Drainage Lift Pipe

●

The installation height of drainage lift pipe shall be less than 280mm.

●

The drainage lift pipe shall be perpendicular to the unit and no more than 300mm from the unit.

Note : The gradient of accessory flexible drainage pipe

①

shall be within 75mm, so that the drainage faucet does not

subject to extra external force.

ST-Joint Confluent Drainage Pipe

Above 100mm

3. After installation is completed, check if the water can be drained smoothly.

●

Fill in 600cc water from the outlet or the check hole slowly to check the draining conditions.

●

After the electrical lines are installed, check the draining conditions in the cooling operation.

Clamp

②

Sponge (Gray)

Flexible Drainage Pipe

①

Big Sponge

⑩

(Accessory)

Clamp

②

(Accessory)

Below 4mm

Roof

Within 300

Suspending Frame Base

Below 280mm

Flexible Drainage

Tube

①

(accessory)

Drainage Lift Pipe

Ceiling

Clamp

②

(accessory)

Содержание AIR C18





























































Результаты поиска

Содержание AIR C18

Отзывы:

GE AIR C18, Руководство по установке, Страница: 49 / 60

Результаты поиска

Содержание AIR C18

Отзывы: