manualshive.com logo in svg

GE 9100c, Техническое справочное руководство

Поделиться
Скачать
GE 9100c Скачать руководство пользователя страница 188

9100c

9-40

M1207026

9.17.2 Replacing Vent

Engine components

Refer to section 6 for Vent Engine components that are to be serviced 
under regular maintenance. Most of the components on the Vent 
Engine can be replaced by removing the mounting screws and 
reusing them to secure the replacement part.

Inlet Filter (A)

Install the filter (with the coarse side DOWN) into the recess in the 
manifold. Place the o-ring into its groove.

PEEP Control Valve (B)

Ensure the valve you are installing (two blue dots) is in this location.

PEEP Safety Valve (C)

Ensure the valve you are installing (white dot) is in this location.

Regulator (D)

Also inspect the two o-rings that seal it to the manifold. Replace as 
necessary.

Supply Pressure Switch

(E)

Also inspect the o-ring that seals it to the manifold. Replace as 
necessary.

Transfer harness wire to top and middle tabs; bottom tab open.

Reservoir (F)

Inspect the two o-rings: reservoir to manifold, reservoir to screw 
head. Replace as necessary.

Note: Do not over tighten the screw securing the reservoir. Over 
tightening could result in cracking the reservoir.

Drive Gas Ports (G)

Inspect the o-ring that seal it to the manifold. Replace as necessary. 
Lubricate o-rings sparingly with Krytox.

MOPV and Free

Breathing Valve Seat (H)

Replace if necessary. 

Inspiratory Flow Valve (I)

Note orientation of the flow valve. Also inspect the two o-rings that 
seal it to the manifold. Replace as necessary.

A

D

C

B

E

I

F

H

G

M1207027

004

MANUAL−DOC, Technical Reference Manual, Technical Reference Manual for 9100c, English−default

Reproduced from the electronic master in MATRIX

Содержание 9100c


















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды