Garmin GDL 82 Скачать руководство пользователя страница 22

Страница: 22 / 68

Installation Materials

190-01810-00

GDL 82 TSO Installation Manual

Rev. 5

Page 3-3

3.2 Optional Accessories

Table 3-5 Optional Accessories

•

Light, indicator, press-to-test, small, MS25041-4

•

Lamp, T-1 3/4, midget flange, MS25237-330

•

Light, indicator, press-to-test, small, MS25041-4

•

Lamp, T-1 3/4, midget flange, MS25237-327

Vendor Contact Information (provided for convenience only):

Amphenol RF, Four Old Newtown Road, Danbury, CT 06810 Phone: (800) 627-7100

www.amphenol.com

3.3 Materials Required but not Supplied

The GDL 82 is intended for use with standard aviation accessories. The following items are required for installation, but
not supplied.

NOTE

If using MIL-W-22759/18, support and protect the wire.

1. Wire (MIL-W-22759/16 or equivalent)

Shielded wire (MIL-C-27500 or equivalent)

Mounting screws

Push/pull (manually resettable) circuit breaker

Tie wraps or lacing cord

Ring terminals (for grounding)

Coaxial cable (RG-400, RG-142B, or equivalent) and connectors

USB-A to USB-B cable (for interface between the computer USB-A receptacle and the GDL 82 USB-B receptacle)

ITEM

GARMIN P/N

MFG P/N

Annunciator, 14VDC

N/A

Annunciator, 28VDC

N/A

Connector, BNC, Male, Clamp

330-00087-00

N/A

Connector, TNC, Male, Clamp

N/A

Amphenol: 031-4452 Not available from Garmin.

GPS 1.57542 GHz Notch Filter

330-00067-00

N/A

Содержание GDL 82





































































Результаты поиска

Содержание GDL 82

Отзывы:

Похожие инструкции для GDL 82

Бренды по названию

Популярные бренды

Garmin GDL 82, Руководство по установке

Результаты поиска

Содержание GDL 82

Отзывы:

Похожие инструкции для GDL 82

Бренды по названию

Популярные бренды