Garmin GDL 82 Скачать руководство пользователя страница 48

Страница: 48 / 68

System Configuration

190-01810-00

GDL 82 TSO Installation Manual

Rev. 5

Page 7-2

7.1 GDL 8X Install Tool

The GDL 8X Install Tool provides:

•

Diagnostics – reports device, system, and faults information

•

Configuration – allows selection of installation options

•

System Update – allows upload of software and firmware to the GDL 82 unit

GDL 8X Install Tool Requirements:

1. To install the GDL 8x Install Tool, administrative rights may be required.

Laptop or PC to run GDL 8X Install Tool. The laptop or PC requirements:

Operating system

Windows 7 or later

Processor speed

850 MHz

Hard drive free memory

500 MB

RAM memory

256 MB

Winzip

(or equivalent application) to extract downloaded file

USB-A

USB-B

USB-A to USB-B adapter cable to interface between a computer USB-A receptacle and the GDL 82 USB-B

receptacle installed in the wiring harness. The cable length should not exceed 16 ft.

Figure 7-1 USB-A and USB-B Connectors

GDL 8X Install Tool Instructions

1. Download the GDL 8X Install Tool from the

Dealer Resource Center

and

flyGarmin.com

and install.

Connect the USB-A plug on the adapter cable to the computer.

With the GDL 82 powered down, connect the USB-B plug on the adapter cable to unit.

Apply power to unit.

Start the GDL 8X Install Tool on the computer.

Select GDL 82.

Figure 7-2 GDL 8X Install Tool Selection Page

Содержание GDL 82





































































Результаты поиска

Содержание GDL 82

Отзывы:

Похожие инструкции для GDL 82

Бренды по названию

Популярные бренды

Garmin GDL 82, Руководство по установке

Результаты поиска

Содержание GDL 82

Отзывы:

Похожие инструкции для GDL 82

Бренды по названию

Популярные бренды