Garmin GDL 82 Скачать руководство пользователя страница 27

Страница: 27 / 68

Installation Planning and Considerations

190-01810-00

GDL 82 TSO Installation Manual

Rev. 5

Page 4-4

4.4 Antenna Requirements

4.4.1 L-Band Antenna

NOTE

Certain types of transponder antennas with thin radiator elements are intended for use at 1030 and
1090 MHz. Evaluate these antennas on a model-by-model basis to determine their suitability as UAT
data link antennas.

The GDL 82 requires the existing L-Band Ultra-High Frequency (UHF) antenna(s) meet the following specifications:



Standard 50 ohm vertically polarized antenna with a VSWR < 1.7:1 at 978 MHz and < 1.5:1 at 1090 MHz.



TSO-C66( ), TSO-C74( ), or TSO-C112( ) antennas that also meet the VSWR specification.

The antenna location should be:

Away from major protrusions.

As far away as practical from openings that can affect the radiation pattern (e.g., landing gear doors, access
doors, etc.).

At least 20 inches from any other transponder, TAS/TCAS, DME, or 1030/1090 MHz antennas.

Table 4-2 Acceptable L-Band Antennas

[1] Not recommended for new installations.

MANUFACTURER

PART NUMBER

MODEL/

DESCRIPTION

CONNECTOR

TYPE

NOTES

Aero Antenna

AT130-16

DME Transponder

TNC

DC Grounded

Comant

CI-100 [1]

DME Transponder

BNC

Open Circuit

CI-100-2 [1]

DME Transponder

TNC

Open Circuit

CI-105 [1]

DME Transponder

BNC

Open Circuit

CI-105-3 [1]

DME Transponder

BNC

Open Circuit

CI-105-16 [1]

DME Transponder

BNC

Open Circuit

CI-110-40-30

DME Transponder

Open Circuit

CI-110-41-30

DME Transponder

DC Grounded

CI-110-60-30

DME Transponder

Open Circuit

CI-110-61-30

DME Transponder

DC Grounded

Dayton-Granger

L10-611-( )

L-Band Blade

Varies

DC Grounded

Garmin

590-0052 or

013-00219-00 [1]

A-40

TNC

Open Circuit

590-0051 or

013-00174-00

A-41

TNC

DC Grounded

Содержание GDL 82





































































Результаты поиска

Содержание GDL 82

Отзывы:

Похожие инструкции для GDL 82

Бренды по названию

Популярные бренды

Garmin GDL 82, Руководство по установке

Результаты поиска

Содержание GDL 82

Отзывы:

Похожие инструкции для GDL 82

Бренды по названию

Популярные бренды