manualshive.com logo in svg

Garmin GDL 82, Руководство по установке

Garmin GDL 82 - компактное устройство для установки на бортовой компьютер, обеспечивающее связь с земными станциями. Для правильной установки и использования рекомендуем скачать бесплатное руководство по монтажу на manualshive.com. Важно ознакомиться с инструкцией перед началом эксплуатации.

Поделиться
Скачать
background image

Installation Procedures

190-01810-00

GDL 82 TSO Installation Manual

Rev. 5

Page 6-1

6

Installation Procedures

6.1 

Cabling and Wiring General Instructions ........................................................................................................ 6-1

6.1.1 Shielded 

Cable 

Preparation...................................................................................................................... 6-2

6.1.2  Instructions to Crimp Pins to Wires .......................................................................................................... 6-3
6.1.3 Backshell 

Assembly.................................................................................................................................. 6-4

6.2 Coaxial 

Cable 

Installation............................................................................................................................... 6-6

6.3 Unit 

Installation ............................................................................................................................................. 6-7

6.4 

Antenna Installation and Connections............................................................................................................ 6-8

6.4.1 GPS 

Antenna........................................................................................................................................... 6-8

6.4.2  GPS Antenna Doubler ............................................................................................................................. 6-9

This section provides guidance necessary for GDL 82 installation. Perform steps in the order presented. All materials 
needed are identified in section 3.

6.1   Cabling and Wiring General Instructions

CAUTION

ENSURE THERE ARE NO WIRING ERRORS BEFORE CONNECTING THE CABLES. INCORRECT WIRING 
COULD DAMAGE COMPONENTS.

NOTE

Shield terminations to the GDL connector backshell must be less than 3.0". Shield terminations for 
interfaced equipment should be as short as practical. Wiring must be shielded as required in section 10.

Install wire in accordance with AC 43.13-1B chapter 11. Allow adequate space for installation of cables and 
connectors. For connector and tooling information, refer to section 3. The installer supplies and fabricates all cables 
according to information in this manual. Cable lengths will vary depending on installation. Ground and shield 
terminations of interfaced equipment can vary. For more information, refer to the equipment manufacturer’s 
installation manual. The following considerations should also be addressed.

•

Cable harness should not be located near controls/control cables, high voltage, electrical noise sources, or fuel 

lines

•

Cable harness should be in a protected area of the aircraft (e.g., isolated from engine rotor burst)

•

Use wire gauge specified in section 10

•

Route and secure the wire bundle as appropriate

•

Avoid sharp bends and chafing

•

Pigtail lengths must be less than 3.0 inches

Содержание GDL 82





































































Отзывы:

Нет отзывов

Похожие инструкции для GDL 82

Uniden Cell Phone Reference Manual preview
Cell Phone
Бренд: Uniden Страницы: 31
Harman Kardon AVR 235 Quick Start Manual preview
AVR 235
Бренд: Harman Kardon Страницы: 4
Harman Kardon AVR 225 Quick Start Manual preview
AVR 225
Бренд: Harman Kardon Страницы: 4
Harman Kardon AVR 1510 Quick Start Manual preview
AVR 1510
Бренд: Harman Kardon Страницы: 11
Harman Kardon AVR 135 Owner'S Manual preview
AVR 135
Бренд: Harman Kardon Страницы: 48
Harman Kardon AVR 120 Service Manual preview
AVR 120
Бренд: Harman Kardon Страницы: 118
Harman Kardon AVR 110 Specifications preview
AVR 110
Бренд: Harman Kardon Страницы: 2
Harman Kardon AVR 1650 Quick Start Manual preview
AVR 1650
Бренд: Harman Kardon Страницы: 10
Harman Kardon AVR 145 Brochure & Specs preview
AVR 145
Бренд: Harman Kardon Страницы: 52
ICS Nav6 Manual preview
Nav6
Бренд: ICS Страницы: 5
Yaesu VR-5000 Brochure & Specs preview
VR-5000
Бренд: Yaesu Страницы: 4
Sandstrom SHDFSAT14 User Manual preview
SHDFSAT14
Бренд: Sandstrom Страницы: 36
Blaupunkt MIAMI620 Instruction Manual preview
MIAMI620
Бренд: Blaupunkt Страницы: 17
Yaesu FTM-3207DR Advance Manual preview
FTM-3207DR
Бренд: Yaesu Страницы: 35
Oxygen 3-8-1000-0 Manual preview
3-8-1000-0
Бренд: Oxygen Страницы: 2
Feniex STORM PRO C-4014 Instruction Manual preview
STORM PRO C-4014
Бренд: Feniex Страницы: 13
Harman Kardon HK 3490 Brochure & Specs preview
HK 3490
Бренд: Harman Kardon Страницы: 24
Interlogix ATS1745 Installation And Setup Manual preview
ATS1745
Бренд: Interlogix Страницы: 27

Бренды по названию

Популярные бренды

Загрузить еще бренды