Follow the precautions below for optimal
product performance and to reduce the risk of
property damage, personal injury, and/or death.
WARNING
: Always wear safety glasses, a dust mask,
and ear protection when installing.
WARNING
: When the boat is placed in the water,
immediately check for leaks around the screws and
any other holes drilled in the hull.
CAUTION
:
P48W
—
Operate at 200kHz only
.
Operating at any other frequency will permanently
damage the transducer and/or the echosounder.
CAUTION
:
TM150M
CHIRP transducer
—Always
operate the transducer in water. Operating in air will
allow the transducer to overheat resulting in failure.
CAUTION
: The bracket protects the sensor from
frontal impact only.
CAUTION
: Never pull, carry, or hold the transducer by
its cable; this may sever internal connections.
CAUTION
: Never strike the transducer with anything
except the palm of the hand to release it.
CAUTION
: Never use solvents. Cleaner, fuel, sealant,
paint and other products may contain solvents that can
damage plastic parts, especially the transducer’s face.
IMPORTANT
:
Read the instructions completely
before proceeding with the installation. These
instructions supersede any other instructions in your
instrument manual if they differ.
17
-4
99
-0
2-
re
v.0
2
06
/30
/16
Transom
or Optional
Trolling-motor Mount
CHIRP
or
Adjustable Wide-beam Transducer
Models:
P48W, TM150M
U.S. Patents 7,369,458; 7,961,522; 8,582,393. UK 2 414 077
Applications
• Recommended for boat up to 7m (22’) long
• Not recommended for boats with large inboard engine(s)
•
P48W
—Not recommended for stepped transoms because the
transducer will be difficult to adjust.
• Vertically orients sound beam on hull with deadrise angle up to 22°
• Adjusts to transom angles from 2
°
– 22
°
• Requires 89mm (3-1/2") of headroom to install
• Release bracket protects sensor from frontal impact only
•
P48W
—Trolling Motor Kit adapts transducer for use with a
trolling motor or optional Portable Bracket
Record the information found on the cable tag for future reference.
Part No._________________Date___________Frequency________kHz
INSTALLATION INSTRUCTIONS
OWNER’S GUIDE &
TM150M
P48W
Tools & Materials
Safety glasses
Dust mask
Ear protection
Phillips screwdrivers
Pencil
Electric drill
Drill bits:
Bracket holes
4mm, #23,
or
9/64"
Transom hole (optional)
18mm, 11/16",
or
3/4"
24 mm or 15/16" or 1"
(Raymarine only)
Cable clamp holes
3mm
or
1/8"
Masking tape
Angle finder (some installations)
Marine sealant (suitable for below waterline)
Straight edge
Grommet(s) (some installations)
Cable ties (some installations)
Band clamp
(trolling motor mount) Measure before purchasing (Figure 8)
Water-based anti-fouling paint (
mandatory in salt water
)
Transom Mount
Attaching the Bracket to the Transom Housing
1. Insert the transom housing’s pivot posts into the recesses on the
sides of the bracket (see Figure 1).
2. Press the two nuts into the slots in the back of the bracket.
3. Align the holes in the transom housing, bracket, and nuts. Insert
the two machine screws capturing the nuts. Tighten the machine
screws until the housing will stay in the “up” (released) position
unaided.
Figure 1. Attaching the bracket to the transducer
pivot post (2)
recess (2)
bracket
nuts
machine
screw (2)
slot (2)
Copyright © 2008 - 2015 Airmar Technology Corp.
transom
housing