Garland MWE3S Скачать руководство пользователя страница 22

Страница: 22 / 72

SERVICE MANUAL

GARLAND CLAMSHELL GRILLS WITH PRODUCT RECOGNITION

PART #4526396 (03/30/10)

Page 22

DESCRIPTION OF GRILL CONTROL

POSSIBLE�ERROR�MESSAGES

GRILL�PROBE�ERROR�

– A grill probe circuit error for the Front, Middle, or Back zone has occurred.

PLATEN�PROBE�ERROR�

– An upper platen probe circuit error has occurred.

HEATER�ERROR�

– Occurs when the controller does not detect a temperature rise in six (6) minutes.

HIGH�TEMP�

– Occurs when the controller senses a temperature of 465˚ F (241˚ C).

CHECK�REED�SWITCH�/�USE�FLAT�COOK�

– One or more of the reed switches are out of adjustment. User will only be able

to cook FLAT menu items.

ERROR�COMMS

- A communications error has occured between the Motor Speed Control and the Main Control.

PLATEN�NOT�LEVEL�

– Occurs if the calibration difference between the front and rear is greater than maximum allowance.

Product Recognition (Auto) and manual cooking is DISABLED. Flat Menu cooking is ONLY allowed.

CHECK�PLATEN�LEVEL�

– Occurs if the calibration difference between the front and rear is greater than the minimum

allowance, but less than the maximum allowance. Product Recognition (Auto) is DISABLED. Perform

CHECK�PLATEN�LEVEL

is displayed, perform the following steps:

1. PRESS AND HOLD the and buttons for 3 seconds. The control will display “AUTO GAP FORCE”.

2. PRESS the button. “NO” will flash on the display. PRESS the button to change it to “YES.”

3. PRESS the button. The platen will immediately lower and reset its internal measurements. Upon completion,

the platen will rise. If the error message does not return continue operating normally. If the error message persists,

level the platen, as shown in section titled “Platen Leveling (Zeroing)”

Power�Button�

– PRESSING and HOLDING the

Power button for 2 seconds will either turn

the controller on or off.

AM/PM�Button�

– In normal operating mode,

toggles between the AM menu library and

the PM menu library.

AUTO/MAN�Button�

– In normal operating

mode, toggles between Automatic Product

Recognition and Manual Cooking.

Up�Arrow�Button�

– In any mode, increases

the value of the flashing cursor character in

the display

Down�Arrow�Button�

– In any mode,

decreases the value of the flashing cursor

character in the display

Right�Arrow�Button�

– In any mode, scrolls

forward through a list

Left�Arrow�Button�

– In any mode, scrolls

backward through a list

Enter�Button�

– In the normal operating

mode, this button is not active. In the

Programming Mode, used to lock in the

values shown on the display.

Program�Button�

– In the normal

operating mode, pressing and holding the

PROGRAM button for 3 seconds enters the

Programming Mode.

Temp�Button�

– In the normal operating

mode, displays the set temperature and the

actual temperature.

Speed�Key�

– In the normal operating mode,

used to change cook time. Also used to enter

Probe Calibration Mode. & Perform Auto

Forced Calibration

Standby�Button�

– In the normal operating

mode, places the grill in Standby Mode.

Содержание MWE3S









































































Результаты поиска

Содержание MWE3S

Отзывы:

Похожие инструкции для MWE3S

Бренды по названию

Популярные бренды

Garland MWE3S, Руководство по обслуживанию

Результаты поиска

Содержание MWE3S

Отзывы:

Похожие инструкции для MWE3S

Бренды по названию

Популярные бренды