English
42/168
English
43/168
- If the mark is above the maximum, you will have
to remove oil from the crankcase. To do this, tilt the
machine and let out a little oil (put a container
at the end of the tube to prevent oil spilling on the
machine or the ground).
NOTE: This machine has an oil sensor to avoid
that the engine starts up with a low level of oil. If
the oil level is not sufficient the engine will not start
(depending on the model).
6.4. START-UP
6.4.1. CHECKPOINTS BEFORE COMMISSIONING
Do not use machine is if it is damaged or incorrectly
regulated.
Use this machine for the purpose for which it was
designed. Any other use may be dangerous for the
user, for the machine and for persons, animals and
things that may be around.
Check:
- The machine completely and look for loose and
damaged parts (screws, nuts, etc.).
- That the moving parts of the machine are not in
contact with any object.
- That the guard is properly attached to the machine.
- That the cutting tool is disengaged (see 6.4.1.1.)
- That there are no fuel leaks.
- The crankcase oil and transmission level.
- The air filter is clean.
Tighten, repair or replace everything you need before
using the machine.
Do not use any accessory on this machine outside of
those recommended by Garland since its use could
result in serious injury to the user, machine, and the
people, animals and things close to the machine.
6.4.1.1. CLUTCH CHECKPOINT
The cutting tool should be off by default to prevent
the machine from moving at the time of starting
the machine. To verify that the clutch is disengage,
place the switch to “O” position and pull slowly and
forcefully from the Starter handle the engine turn. Note
If, while the motor spins, also turn the cutting tool. If the
cutting tool rotates, it means that the clutch is engaged
and is therefore poorly regulated. If the clutch is not
correctly regulated take your machine for service.
6.4.2.STARTING THE ENGINE
Attention: This engine has a system to cut
emissions and limit the contaminating gases from the
exhaust.
When the engine stops, it needs 3 seconds to
eliminate the burnt gases and therefore it has a
security system that will avoid the start up of the
engine during this period of time. For this reason, once
you stop the engine, it will not restart until 30 seconds
pass.
Take into account this indication and always wait
30 seconds to restart the engine once it has been
stopped. If you try to start the engine during this time,
you will not be able to do so until the 30 seconds pass
and the system is reactivated.
Start the engine carefully, in accordance with the
instructions, and feet away from the milling cutters.
Содержание MULE 741 QG
