English
44/168
English
45/168
7. USING THE MACHINE
Use this machine only for the designated
purposes. Using this chainsaw for any other use is
dangerous and can cause bodily harm and/or damage
to the machine.
Do not approach the milling cutters of the rotary tiller
when the motor is running.
Do not start the machine in a room or
enclosure.The exhaust gases and fuel and
oil vapors contain carbon monoxide and
harmful chemicals. In case of a concentration of gases
produced by poor ventilation, remove all that impedes
the flow of clean air to improve ventilation from the
work area and not return to work in the area unless
you have properly ventilated area and have clear that
ventilation is sufficient so that does not happen this
concentration again.
Work only in daylight or good artificial light. Do not use
this machine at night, with fog or with a low visibility
which do not allow you to clearly see the working area.
Limit continued use of this machine to a 10 minute
time limit and between 10 and 20 minutes to rest
between each session.
If you slip or fall, stop acceleration and move the
switch to the “O” position.
Do not use this machine if you are tired, ill, have taken
drugs, narcotic drugs or alcohol. The lack of rest and
fatigue can cause accidents or damage.
Always readjust the machine on a flat and stable surface.
Do not use the machine on steep slopes where you
cannot guarantee their safety. If you are working on
slopes slow down your work pace and ensure you
have good stability.
Be alert when you back-up or pull the machine
towards you.
Do not solely rely on the security features of this
machine.
It is necessary to pay attention to the possible loosening
or overheating of the parts of the machine.
If you detect any anomaly immediately stop the
machine and check it carefully. In case of mechanical
failure take the machine to the technical service for
repair. You should not continue working if you notice
that the operation is not correct.
Remember to always use the machine with clean
hands and without any fuel or oil remains.
Clean the work area and remove all obstacles that may
cause accidents. Check the work area when going to
work and remove all items that could become entangled
in the cutting tool. Also remove all the objects that the
cutting tool can violently eject in the operation.
Do not allow anyone to enter the work perimeter. This
work perimeter must be 15 meters and is a danger zone.
Never leave this machine unattended.
Be careful not to touch the hot parts of the
machine while the engine is running or after
use, such as exhaust, spark plug or high
voltage cables.
Do not use other accessories this machine except
those recommended by our company since its use
could cause severe damage to the user, people close
to the machine and the machine itself.
Always follow the safety rules given in this manual.
Содержание MULE 741 QG
