![background image](http://html1.mh-extra.com/html/garland/mule-341-g/mule-341-g_instruction-manual_3647326037.webp)
English
English
37/136
Do not solely rely on the security features of this
machine.
It is necessary to pay attention to the possible
loosening or overheating of the parts of the machine.
If you detect any anomaly immediately stop the
machine and check it carefully. In case of mechanical
failure take the machine to the technical service for
repair. You should not continue working if you notice
that the operation is not correct.
Remember to always use the machine with clean
hands and without any fuel or oil remains.
Clean the work area and remove all obstacles that may
cause accidents. Check the work area when going to
work and remove all items that could become entangled
in the cutting tool. Also remove all the objects that the
cutting tool can violently eject in the operation.
Do not allow anyone to enter the work perimeter. This
work perimeter must be 15 meters and is a danger zone.
Never leave this machine unattended.
Be careful not to touch the hot parts of the
machine while the engine is running or after
use, such as exhaust, spark plug or high
voltage cables.
Do not use other accessories this machine except
those recommended by our company since its use
could cause severe damage to the user, people close
to the machine and the machine itself.
Always follow the safety rules given in this manual.
7.1. HOLDING AND GUIDING THE MACHINE
While working always place yourself behind the
machine and hold it firmly with both hands on the
handles.
Warning! Do not use this rotary tiller with one
hand.
Warning! This rotary tiller could bounce upwards
or jump forwards unexpectedly. If the teeth hit
something hard that is buried in the ground such as
large stones, roots or trunks, if the soil is too hard or
if the ground is frozen. Always firmly hold the machine
with both hands.
This machine clutch is deactivated (disengaged)
by default, to activate the clutch and for the engine
power to transmit to milling cutters, the clutch lever
must be tightened.
7.2. WORKING WITH THE ROTARY TILLER
Start the machine following the instructions in the
manual.
Milling cutters in motion will pull the machine forward,
you must maintain the appropriate speed more or less
by nailing the spur in the soil.
Slowly move the tiller at the right rhythm so the milling
cutters have time go crumbling the land.
If the tiller sinks and doesn’t go, move the handlebar
left and right until it is released.
When working on slopes it is always slightly more
above the slope so that the machine is always below
you.
7.2.1. USING SUGGESTIONS
A depth of tillage between 15-20 cm is generally
adequate, and rarely there is advantage in deeper. The
shallower tilling is frequently recommended for areas
of little rainfall to conserve moisture.
Содержание MULE 341 G
