![background image](http://html1.mh-extra.com/html/garland/mule-341-g/mule-341-g_instruction-manual_3647326036.webp)
English
36/136
4. Move the air lever in RUN position (ON -
normal work position).
5. If the engine exploded but did not actally start
running, pull the start rope again until it starts.
6. Allow the engine to warm up for approximately one
minute before starting to work with the machine.
6.4.2. STARTING WITH A HOT ENGINE
Place air lever in RUN position (ON) and pull the
start rope until it starts.
If the machine does not start after pulling at the rope
a few times, please refer to the cold start up section.
6.4.3. STOPPAGE
Let go of the accelerator and let the engine run
at idle speed for a few seconds. Stop the engine by
displacing the ON/OFF switch.
7. USING THE MACHINE
Use this machine only for the designated
purposes. Using this chainsaw for any other use is
dangerous and can cause bodily harm and/or damage
to the machine.
Do not approach the milling cutters of the rotary tiller
when the motor is running.
Do not start the machine in a room or
enclosure.The exhaust gases and fuel and
oil vapors contain carbon monoxide and
harmful chemicals. In case of a concentration of gases
produced by poor ventilation, remove all that impedes
the flow of clean air to improve ventilation from the
work area and not return to work in the area unless
you have properly ventilated area and have clear that
ventilation is sufficient so that does not happen this
concentration again.
Work only in daylight or good artificial light. Do not use
this machine at night, with fog or with a low visibility
which do not allow you to clearly see the working
area.
Limit continued use of this machine to a 10 minute
time limit and between 10 and 20 minutes to rest
between each session.
If you slip or fall, stop acceleration and move the
switch to the “O” position.
Do not use this machine if you are tired, ill, have taken
drugs, narcotic drugs or alcohol. The lack of rest and
fatigue can cause accidents or damage.
Always readjust the machine on a flat and stable surface.
Do not use the machine on steep slopes where you
cannot guarantee their safety. If you are working on
slopes slow down your work pace and ensure you
have good stability.
Be alert when you back-up or pull the machine
towards you.
SWITCH STOP
Содержание MULE 341 G
