manualshive.com logo in svg

Garland HEEGM48CL, Руководство по обслуживанию

Поделиться
Скачать
Garland HEEGM48CL Скачать руководство пользователя страница 8

Page 8  |  HEEGM Service Manual part# 4532502 (Rev 0)

4 UNIT CONFIGURATION

The components for this compact model are carefully designed and organized to provide high 
efficiency and safe operation. You will find all the major components illustrated in this section.

For a list of parts and part numbers, please refer to the 

HEEGM Parts List

 (see section “8 Related 

Documents”), available on our website @ www.Garland-Group.com

4.1 Important Features

The features listed below are referenced in the illustrations in “4.1.2 Major Components”.

1

Ignition wires are protected by a metal wire-way and high temperature silicone sleeve.

2

The flue at the back of the unit prevents overheating of the unit and its components.

3

The removable side shields contribute to even temperature and easy cleaning. The side 
shields also prevent the cooking grates, when placed in the elevated position,  from sliding 
off the side of the unit.

4

Solenoid valves connected in series, provide redundancy and ensure safe operation.

5

Left/Right Side Leg Panels are installed using a tab and slot method at the back, which can be 
dislodged and slid out easily when servicing the unit.

6

Additional Main Power Switch for 220-240V units (see figure below).

Burners 

ON/OFF 

Main Power

ON/OFF

120V Single Switch

120V Double Switch

220-240V Single Switch

220-240V Double Switch

24”, 36” models

48”, 60” models

24”, 36” models

48”, 60” models

6

4.2 Major Components - Quantity Comparison

Model No.

Burner

Manifold 
Assembly

Solenoid 
Gas Valve

Ignition Module

Burner ON/OFF 
Switch

4-Spark

6-Spark

HEEGM24CL

4

1

2

1

--

1

HEEGM36CL

6

1

2

--

1

1

HEEGM48CL

9

2

4

1

1

2

HEEGM60CL

11

2

4

--

2

2

Содержание HEEGM48CL













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды