manualshive.com logo in svg

Garland HEEGM48CL, Руководство по обслуживанию

Поделиться
Скачать
Garland HEEGM48CL Скачать руководство пользователя страница 22

Page 22  |  HEEGM Service Manual part# 4532502 (Rev 0)

6 COMPONENTS 

(CONT.)

6.6 Gas Valve

HEEGM__CL models use non-adjustable control valves to regulate the flow of gas to the burners. 

These valves are fixed (no center stem adjustment).

6.6.1 Inspecting a Gas Valve

A damaged, fractured, seized, or restricted valve may result in delayed ignition or may prevent the 
burner from lighting at all. 

To check a valve, turn the valve to HIGH, then light. Then turn the valve to LOW and make sure it 
doesn’t go out. If the valve is seized or hard to turn, replace it.

6.6.2 Removing & Installing a Gas Valve

DANGER

Turn off gas supply and remove main power supply to the unit.

WARNING

Test for gas leaks before returning the equipment into service.

i

IMPORTANT

When reassembling the gas valve and extension, ensure the set-screw is 
tightened against the flat part of the valve.

Bottom View

Valve
Extension

Tighten Set Screw

 against 

the flat area of Gas Valve

Gas Valve

i

IMPORTANT

Ensure the gas valve is tightened onto the manifold such that burner sits 
level when installed on the valve orifice.

To replace a gas valve:

1. 

  

DANGER: Turn off gas supply and remove main power supply to the unit.

2.  Remove the knobs and valve panel (see “6.2 Valve Panel”). Remove the grease chute and/or 

spigot if they are in the way.

3.  Remove the valve extension by loosening the set screw with an allen key.

4.  Use a combination wrench to loosen the valve by sliding the open end of the wrench over the 

orifice and onto the valve body.

Содержание HEEGM48CL













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды